American Dynamics RAS915LS Скачать руководство пользователя страница 102

Страница: 102 / 124

Vicon Command Summary

The following table lists the Vicon controller key sequence to control the indicated SpeedDome Ultra
VII functions.

If you want to …

Use …

Set

Auto Iris

ON/OFF

(LED indicates Auto Iris state: ON = AUTO)

A/I

Toggles state

Set

Auto Focus ON/OFF

(LED indicates Auto Focus state: ON = AUTO)

Press and Hold

L-Spd

A/P

Toggles state

Goto Presets

Run/Pgm switch to

RUN

Enter 1-79 Enter

Program Presets

Run/Pgm switch to

PGM

Enter 1-79 Enter

Run

PEEL Pattern and Repeat

AUX5

Rotate dome 180° (“Flip”)

AUX6

Start

Pattern

1-3

Definition

Run/Pgm switch to

PGM

Enter 80-82 Enter

End

Pattern Definition

Run/Pgm switch to

PGM

Enter 86 Enter

Review Pattern

Run/Pgm switch to

PGM

Enter 87 Enter

Accept Pattern

Run/Pgm switch to

PGM

Enter 88 Enter

Run Pattern

1-3

Run/Pgm switch to

RUN

Enter 80-82 Enter

Repeat Pattern 1-3

Run/Pgm switch to

RUN

Enter 83-85 Enter

Set Pattern to Peel

Enter 89 Enter

Vphase Dome

Note:

The A/I LED blinks indicating that you are in the vphase

mode. Enter key sequence again to turn vphase adjustment off.
The A/I LED stops blinking and indicates Auto Iris State.

Run/Pgm switch to

PGM

Enter 93 Enter

•

Pan Right

to increment

•

Pan Left

to decrement

Start

Dome Configuration Menu

See Operating the Dome Configuration Menu on page F–3.

Enter 94 Enter

Turn

IR Mode On

Run/Pgm switch to

PGM

Enter 95 Enter

Turn

IR Mode Off

Run/Pgm switch to

PGM

Enter 96 Enter

Reset Dome

Run/Pgm switch to

PGM

Enter 97 Enter

F–2

SpeedDome Ultra VII Operator's Manual

Содержание RAS915LS





























































































































Результаты поиска

Содержание RAS915LS

Отзывы:

Бренды по названию

Популярные бренды

American Dynamics RAS915LS, Руководство оператора

Результаты поиска

Содержание RAS915LS

Отзывы:

Бренды по названию

Популярные бренды