background image

ProbleM

unit will not run

cauSe

1) No air supply to unit.

2) faulty air supply line.

SolutioN

1) connect air supply.

2) Perform maintenance and check line to air

supply.

unit runs but fan
makes loud scraping
noise.

unit runs but vibrates
excessively.

unit runs but fan does
not turn.

unit runs but does not
develop full power.

1) unit has been severely jolted

causing fan to rub against
housing.

2) unit has been severely jolted

causing housing to deform.

1) Severe jolt has bent motor shaft

causing unit to be out of
balance.

2) fan blade damaged.

3) Dirt built up on one side of fan

blade.

1) fan is jammed.

2) housing has been damaged and

presses on the fan blade.

1) low air supply pressure.

2) low air supply cfm.

3) excessive duct length.

4) Worn motor vanes.

1) remove motor and replace damaged motor

mounts.

2) Perform maintenance and check line to air

supply.

1) remove and replace motor. replace fan

blade as necessary.

2) replace fan blade.

3) clean fan blade.

1) remove motor and replace damaged motor

mounts.

2) replace fan blade if necessary.

3) replace housing/unit as necessary.

1) Supply 100 psi air.

2) increase size of compressor and/or size of

supply lines to provide at least 71 cfm.

3) reduce duct length to recommended

maximum.

4) rebuild motor.

GENERAL TROUBLE SHOOTING GUIDE

ruNS GooD

theN SloWS

DoWN

ruNS

hot

WoN’t ruN

at all

loW

SPeeD

loW

torque

reaSoN

MOTOR TROUBLE SHOOTING GUIDE

Dirt, foreign Material

x

x

x

internal rust

x

x

x

Misalignment

x

x

x

x

x

insufficient air Pressure

x

x

too Small of air line

x

x

restricted exhaust

x

Poor lubrication

x

x

x

x

jammed Machine

x

x

x

x

compressor too Small

x

x

compressor too far 

from unit

x

x

7

Содержание VAF-3000P















Отзывы: