Am186™CC/CH/CU Microcontrollers User’s Manual
5-1
CHAPTER
5
CHIP SELECTS
5.1
OVERVIEW
Signals that allow the CPU to select specific memory or peripheral devices are called
chip
selects.
The microcontroller provides six chip select outputs for use with memory devices (UCS,
LCS, and MCS3–MCS0) and eight chip selects for use with peripherals (PCS7–PCS0) in
either memory or I/O space. The six memory chip selects can be used to address three
memory ranges. Each peripheral chip select addresses a 256-byte block offset from a
programmable base address in memory or I/O.
The microcontroller can sense a ready signal for each of the memory or peripheral chip
select lines. The R2 bit in each of the memory chip select control registers determines
whether the external ready signal is required or ignored.
In addition, the R1–R0 bits in each of the memory chip select control registers control the
number of wait states inserted in the bus cycle. Although most memory and peripheral
devices can be accessed with three or fewer wait states, some slower devices cannot. This
feature allows devices to use externally generated wait states to slow down the bus.
Address and data bus size options and enabling or disabling the address bus during the
address phase of a bus cycle are configured on a chip select basis. UCS and LCS can also
be configured for DRAM support.
The chip select lines are active for all memory and I/O cycles in their programmed areas,
whether they are generated by the CPU or by the integrated DMA unit.
The UCS and LCS chip selects assert relative to the timing of the nonmultiplexed address
(A) bus; the MCS and PCS chip selects assert relative to the multiplexed address and data
(AD) bus. The timing for chip selects is shown in the data sheets for each of the Am186CC/
CH/CU microcontrollers.
The CAS0 and CAS1 signals can be used to perform byte writes in a manner similar to
WLB and WHB, respectively. That is, CAS0 corresponds to the low byte (WLB) and CAS1
corresponds to the high byte (WHB).
Содержание Am186 CC
