Synchronous Serial Port (SSI)
14-8
Am186™CC/CH/CU Microcontrollers User’s Manual
Figure 14-5
SSI Single-Transmit, Multiple-Receive with SDEN as External Device Enable
14.5.4
Software-Related Considerations
The SSI interface allows for a variety of software and hardware protocols:
■
Signaling a read/write: In general, software uses the first write to the SSI to transmit
an address or count to the peripheral. This value can include a read/write flag in the
case where the device supports both reads and writes.
■
Using SSTXD1 as an address register: The SSTXD1 register can be an address
register that holds the value of the last address accessed, and the SSTXD0 register can
be the data transmit register. In this case, the current value in the SSTXD1 register can
be used by software to generate the next address or to determine if the last transaction
was a read or a write.
■
Using SSTXD1 and SSTXD0 as transmit registers for two peripheral devices: In
some systems, it may clarify the code and aid in debugging to view the two data transmit
registers as unique to different peripheral devices. This allows the last value transmitted
to each device to be examined by debug code.
14.5.5
Comparison to Other Devices
The SSI is mostly backward-compatible with software written for the Am186EM SSI.
Additional features have been added to the SSI implementation. In its default mode, the
SSI on the Am186CC/CH/CU microcontrollers is backward-compatible with the Am186EM
with the following exceptions:
■
The SSI status and configuration register locations in the address map are different.
SDEN
SCLK
Set
DE0
bit
Write
transmit
register
PB=0
DR/DT=0
PB=1
DR/DT=0
PB=1
PB=0
DR/DT=1
Read
receive
register
PB=1
PB=1
DR/DT=0
Read receive
PB=1
PB=0
DR/DT=1
PB=1
DR/DT=0
PB=0
DR/DT=1
Clear
DE0
bit
PB=0
DR/DT=0
SDATA
(dummy
read)
Read receive
register (returns
data from last
transaction to CPU
without generating
another SSI transfer)
register (returns
data from last
transaction to CPU
and generates another
SSI transfer)
MSB(Reverse shift order)LSB
Notes:
SDEN is configured to be active Low in the scenario shown above.
Any PIOs used as SSI enables should be inactive while SDEN is active.
The SSI data order is configured to be in Reverse mode (MSB first).
The SSI clock is configured to be in Normal mode.
Содержание Am186 CC
