AMCI SD4840EK Скачать руководство пользователя страница 60

Страница: 60 / 104

OMMAND

ATA

ORMAT

SD4840EK User Manual

ADVANCED MICRO CONTROLS INC.

CMD_word0

Figure R6.2 CMD_word0 Format

Bit 15: Mode_Select –

“0” for Command Mode programming.

It is possible to write configuration data to the unit using the output words, but the use of this

method is discouraged. Configuration data should be written to the SD4840EK using the CoE

interface as described in the previous chapter.

Bit 14: Preset_Encoder –

When set to “1” the SD4840EK will preset the Encoder Position to the value

stored in the DINT Position output register.

Bit 13: Run_Assembled_Move –

When set to “1” the SD4840EK will run the Assembled Move already

stored in memory.



Assembled_Move_Type – CMD_word1, Bit 9:

This bit determines the type of move that is

run. When this bit equals “0”, a Blend Move is run. When this bit equals “1”, a Dwell Move is

run. When starting a Dwell Move, the Dwell Time is programmed with the UINT Jerk output

65,536.



Reverse_Blend_Direction – CMD_word1, Bit 4:

This bit is used to determine the direction that

the Blend Move will be run in. When this bit equals “0”, the Blend Move runs in the clockwise

direction. When this bit equals “1”, the Blend Move is run in the counter-clockwise direction.

Bits 11 & 12: Program_Assembled & Read_Assembled_Data –

These bits are used to program the seg-

ments of an Assembled Move before the move can be run. Their use is explained in the

Assembled

Move Programming

section of this manual starting on page 33.

Bit 10: Reset_Errors –

When set to “1” the SD4840EK will clear all existing errors and reset the

Move_Complete

bit. A driver fault will be cleared if the Clear_Driver_Fault bit, (CMD_word1, bit

10), is set to “1” when the Reset Errors command is issued.

Bit 9:

Preset_Position –

When set to “1” the SD4840EK will preset the Motor Position to the value stored

in the DINT Position output register and reset the Move_Complete bit in the Network Input Data.

Bit 8:

Jog_CCW –

When set to “1” the SD4840EK will run a Jog Move in the counter-clockwise direc-

tion. The full explanation of a

CW/CCW Jog Move

can be found starting on page 26.



Registration_Move – CMD_word1, Bit 7:

When this bit equals “0”, and a Jog Move



command is issued, it will run as a standard Jog Move. When this bit equals “1” and a Jog



Move command is issued, the move will run as a Registration Move.



Enable_Electronic_Gearing – CMD_word1, Bit 6:

When this bit equals “1” the SD4840EK

will switch its operation to

Electronic Gearing

mode as described on page 36. While in this

mode, the two Jog Move bits are used to enable motor motion. One of these two bits must equal

“1” before the motor will follow a change in encoder position.

CMD_word0

15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

Prst

_Enc

Run_A

d_A

Dat

g_A

RSet

_Er

st_

Jog_CCW

Jog_CW

Hom

e_CCW

me_CW

I-

ld_

Содержание SD4840EK









































































































Результаты поиска

Содержание SD4840EK

Отзывы:

Похожие инструкции для SD4840EK

Бренды по названию

Популярные бренды

AMCI SD4840EK, Руководство пользователя

Результаты поиска

Содержание SD4840EK

Отзывы:

Похожие инструкции для SD4840EK

Бренды по названию

Популярные бренды