manualshive.com logo in svg

AMCI ANR2, Руководство пользователя

Поделиться
Скачать
AMCI ANR2 Скачать руководство пользователя страница 33

20 Gear Drive, Plymouth Ind. Park, Terryville, CT 06786

Tel: (860) 585-1254  Fax: (860) 584-1973  http://www.amci.com

33

CHAPTER 4

AMCI N

ET

 C

ONFIGURATOR

 S

OFTWARE

The AMCI NET Configurator software is a simple utility program.  As such, it assumes that it 
has exclusive access to the AnyNET-I/O Stack.  Do not attempt to run this software utility while 
the AnyNET-I/O Stack is attached to a host controller.  Doing so may result in communication 
contention that will prevent the Configurator software utility from communicating with the rack, 
may interrupt communication between the host controller and the AnyNET-I/O Stack, and may 
require you to cycle power to the AnyNET-I/O stack or host controller to rectify the problem.

The following images only show the different screens available on the NET Configurator software for setting 
up an ANR2 module.  Information on installing the software and using it to configure your network interface 
is available in the network interface manual that is appropriate for your AnyNET-I/O Stack.

ANR2 Configuration Screen

Figure 4.1 shows the settings on the Configuration tab.  This is where you set all of the 

ANR2 Programmable 

Parameters

 that are described on page 9. The bottom half of the screen shows the module and channel status 

data being transmitted from the ANR2.  This data is described in the 

Status Bits

 section of this manual start-

ing on page 16.  

Figure 4.1  NET Configurator: Configuration Screen

The AMCI NET Configurator software version 4.20 and above adds screens that 
allow you to graphically program the parameters of an ANR2 module as well as 
display position and velocity data.  This software is designed to assist you in gain-
ing familiarity with the ANR2, but is not meant to replace programming your host 
controller.

Содержание ANR2































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды