manualshive.com logo in svg

AMCI ANR2, Руководство пользователя

Поделиться
Скачать
AMCI ANR2 Скачать руководство пользователя страница 30

INSTALLING THE ANR2

ADVANCED MICRO CONTROLS INC.

3

30

 

Extending the Transducer Cable  (continued)

6-Wire Ratiometric

Figure 3.19  Extending a 6-Wire Ratiometric Sensor Cable

It is important to note the sense of the secondary windings and wire them appropriately.  One 
of the secondary windings must be in phase with the primary and one must be in anti-phase.  
The sensor will not work if one of the secondary windings is reversed.  The sensor will count 
in the opposite direction if both of the phases are reversed.

Avoiding Ground Loops When Extending the Sensor Cable

A ground loop occurs when the shields of a cable are attached to earth ground in two places.  It is possible, 
and the likelihood increases as the cable length increases, for these two earth ground points to have a voltage 
potential between them.  The shield acts as a low impedance path between the two points which results in a 
constant current flowing through the shield.  To avoid a ground loop, the cable shields must not be grounded 
in two places.  

If the shield of the sensor cable is isolated from the body of the sensor, connect the shield of the sensor 
cable to the shields of the Belden cable and ground the shield at the ANR2.  Treat the shield of the sen-
sor cable as a signal carrying conductor and do not connect it to earth ground at any other point.

If the shield of the sensor cable is connected to the body of the sensor but the body of the sensor is iso-
lated from chassis ground by its mounting, connect the shield of the sensor cable to the shields of the 
Belden cable and ground the shield at the ANR2.  Treat the shield of the sensor cable as a signal carry-
ing conductor and do not connect it to earth ground at any other point.

If the shield of the sensor cable is connected to the body of the sensor and the body of the sensor is con-
nected to earth ground by its mounting, 

Do Not

 connect the shield of the sensor cable to the shields of 

the Belden cable.  The shield of the sensor cable is grounded by the sensor body.  Connect the shields of 
the Belden cable to earth ground at the ANR2.

B

A

B

+Exc

+Exc

Shields

–Exc

–Exc

GND

A

GND

GND

LVDT/RVDT

Sensor

RED

WHITE

BLACK

BLACK

BLACK

GREEN

Belden 9730 or equ.

NOTE:

 Connection should only be

made if the sensor’s shield is isolated 
from sensor body or sensor body is 
not grounded.  Connection must be 
isolated from Earth Ground at this point.

Содержание ANR2































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды