Ambit PIB v1.5 Скачать руководство пользователя страница 12

Страница: 12 / 72

Section 1 • Introduction

• Do not touch the sterile open end of tubing. Use the aseptic technique utilized by

your facility.

• Do not re-sterilize cassette.

1.2.2

Protection From Air Infusion

• The solution must be provided in a non-vented, collapsible container.

• Remove all air from solution container and tubing before use.

• For IV applications, the ambIT® PIB

v1.5

pumps should be used with air elimination

filters because air protection is not provided.

1.2.3

Protection From Unintended Bolus

• The unintended bolus volume that could be released into a patient prior to clearing

a downstream occlusion may be released by breaking the seal on the connection

between the pump and the catheter.

• Breaking the connection between the catheter and the pump may introduce

contamination into the fluid path. Do not try to clear the unintended bolus volume

if any concerns exist about introducing contamination.

•

The maximum unintended bolus volume released into the patient when occluded

on the downstream side is between 0.050 and 0.10 ml. One stroke of an infusion is

0.050 ml. Since these amounts are similar, there is no risk of over-infusing and the

unintended bolus may not need to be removed.

1.2.4

Use of ambIT

PIB·

v1.5

Pumps in MRI Environment

Safety in MRI not evaluated. The ambIT

PIB·

v1.5

pumps have not been evaluated for

safety and compatibility in the MRI environment. The pumps have not been tested for

heating, migration, or image artifact in the MRI environment. The safety of the ambIT

PIB

v1.5

pumps in the MRI environment is unknown. Scanning a patient who has the

device may result in patient injury.

1.3

Indications for Use

The ambIT

PIB

v1.5

pumps are

used to infuse medicines and/or fluids into patients primarily

for pain management.
The routes of administration are generally intravenous, epidural, and/or regional.
The ambIT

PIB

v1.5

pumps are not intended to supersede, augment, or replace any other

medical device or drug indications for use or intended uses.
The ambIT

PIB

v1.5

pumps are intended to be used in the home and in healthcare facilities.

NOTE:

Any use of the pumps other than those indicated above is regarded as an off-

label use. The ambIT

PIB

v1.5

pumps are not equipped with an air detection

circuit, therefore if infusion of air could cause harm to the patient, it is

recommended to use a filtered cassette or air elimination filter.

Содержание PIB v1.5









































































Результаты поиска

Содержание PIB v1.5

Отзывы:

Похожие инструкции для PIB v1.5

Бренды по названию

Популярные бренды

Ambit PIB v1.5, Руководство для клиницистов

Результаты поиска

Содержание PIB v1.5

Отзывы:

Похожие инструкции для PIB v1.5

Бренды по названию

Популярные бренды