background image

 

Version 1.0  

 

©Copyright 2018, Ambient LLC. All Rights Reserved. 

 

 

 

Page 13 

This product is not a toy. Keep out of the reach of children. 
 
No part of this manual may be reproduced without written authorization of the manufacturer. 
 
Ambient,  LLC  WILL  NOT  ASSUME  LIABILITY  FOR  INCIDENTAL,  CONSEQUENTIAL, 
PUNITIVE,  OR  OTHER  SIMILAR  DAMAGES  ASSOCIATED  WITH  THE  OPERATION  OR 
MALFUNCTION OF THIS PRODUCT. 

10.

 

FCC Statement 

Statement according to FCC part 15.19: 

 

This device complies with part 15 of the FCC rules. Operation is subject to the following two 
conditions:   

1.

 

This device may not cause harmful interference.   

2.

 

This device must accept any interference received, including interference that may cause 
undesired operation.   
 

Statement according to FCC part 15.21: 

 

Modifications not expressly approved by this company could void the user's authority to operate the 
equipment. 

Statement according to FCC part 15.105: 

 

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, uses and 
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications.   
However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which can be determined 
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:   

 

Reorient or relocate the receiving antenna.   

 

Increase the separation between the equipment and receiver.   

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.   

 

Consult the dealer or an experienced radio/TV technician for help.   

 

11.

 

  Warranty Information 

Ambient,  LLC  provides  a  1-year  limited  warranty  on  this  product  against  manufacturing  defects  in 
materials and workmanship. 
 
This limited warranty begins on the original date of purchase, is valid only on products purchased and 
only to the original purchaser of this product. To receive warranty service, the purchaser must contact 
Ambient, LLC for problem determination and service procedures.   
 
Warranty service can only be performed by a Ambient, LLC. The original dated bill of sale must be 
presented upon request as proof of purchase to Ambient, LLC. 
 
Your  Ambient,  LLC  warranty  covers  all  defects  in  material  and  workmanship  with  the  following 
specified exceptions: (1) damage caused by accident, unreasonable use or neglect (lack of reasonable 
and necessary maintenance); (2) damage resulting from failure to follow instructions contained in your 
owner’s manual; (3) damage resulting from the performance of repairs or alterations by someone other 

Содержание RC-8365















Отзывы: