Amazone Precea 4500-2 Скачать руководство пользователя страница 73

Страница: 73 / 256

Secure the tractor and implement.

When working at night, switch on the interior
lighting of the fertiliser hopper.

Climb onto the loading board using the steps.

To unfold the ladder,

see "Operating the loading board with ladder".

Open the rubber straps

Open the fertiliser hopper tarpaulin

Remove residues or foreign objects from the
fertiliser hopper.

Fill the fertiliser hopper.

10. Close the fertiliser hopper tarpaulin with the pull

rope

11. Secure the fertiliser hopper tarpaulin with rubber

straps.

12.

To fold the ladder,

see "Operating the loading board with ladder".

CMS-I-00001892

6.5.4.2 Filling the fertiliser hopper with the folding filling auger

NOTE

The guard screen and function screen in the
fertiliser hopper are closed. Only a closed guard
screen and function screen can prevent fertiliser
clumps and/or foreign objects from entering the
fertiliser hopper and clogging the metering unit.

CMS-T-00011012-A.1

6 | Preparing the machine

Preparing the implement for operation

MG6149-EN-GB | J.1 | 18.10.2022 | © AMAZONE

Содержание Precea 4500-2

































































































































































































































































Результаты поиска

Содержание Precea 4500-2

Отзывы:

Бренды по названию

Популярные бренды

Amazone Precea 4500-2, Оригинальное руководство по эксплуатации

Результаты поиска

Содержание Precea 4500-2

Отзывы:

Бренды по названию

Популярные бренды