manualshive.com logo in svg

Amazone Precea 4500-2, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 4500-2 Скачать руководство пользователя страница 207

7.

Install the dust caps.

8.

Install the depth control wheel along with the
bracket.

10.1.4 Adjusting the cutting disc drive on the PreTeC mulch seeding coulter

INTERVAL

Every 50 operating hours

or

Every 3 months

1.

Remove the bolt 

2

.

2.

Remove the depth control wheel 

1

.

The depth control wheel drives the cutting disc
through rotation.

3.

To ensure that the depth control wheel 

1

slightly touches the cutting disc 

6

,

adjust the distance of the depth control wheel

with the spacer discs 

3

 and 

4

.

4.

Spacer discs that are not needed are fastened to
the depth control wheel arm 

5

.

Fasten the discs on the opposite side using the
bolt.

2

3

4

5

1

6

175 Nm

CMS-I-00002016

CMS-T-00002377-G.1

10 | Repairing the machine

Maintaining the machine 

MG6149-EN-GB | J.1 | 18.10.2022 | © AMAZONE

201

Содержание Precea 4500-2

































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды