manualshive.com logo in svg

Amazone Precea 4500-2, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 4500-2 Скачать руководство пользователя страница 185

Seed is not caught and jumps out of the furrow

NOTE

If the seed collides against the catch roller 

1

 or

the seed furrow 

2

, it is not reliably caught. The

position of the catch roller can be adjusted.

The position of the catch roller must be adjusted
by trained specialist personnel.

Contact your specialist workshop.

CMS-I-00001925

Control terminal shows a spread rate error

1.

Remove the spring cotter pin 

1

.

2.

Press the shot channel 

2

 down against the

spring element 

3

.

3.

Remove the shot channel upwards.

4.

Clean the shot channel.

5.

Install the shot channel.

6.

Secure the shot channel with a spring cotter pin

1

.

2

1

3

CMS-I-00002040

Blocking of the press rollers

NOTE

Offset installation is not possible in conjunction
with disc closers.

1.

Unscrew the nut 

1

 and remove it.

2.

Remove the press roller.

3.

To increase the throughput on the press rollers,

install the press roller with offset.

1

2

3

CMS-I-00002041

CMS-T-00002347-C.1

CMS-T-00002348-B.1

CMS-T-00002373-B.1

8 | Eliminating faults

 

MG6149-EN-GB | J.1 | 18.10.2022 | © AMAZONE

179

Содержание Precea 4500-2

































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды