manualshive.com logo in svg

Amazone Precea 3000-A, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 3000-A Скачать руководство пользователя страница 48

Hydraulic system

Maximum operating pressure

210 bar

Tractor pump output

Implement with mechanical fan drive, at least 20 l/min at 150 bar

Implement with hydraulic fan drive, at least 50 l/min at 150 bar

Implement hydraulic oil

HLP68 DIN51524

The hydraulic oil is suitable for the combined hydraulic oil circuits

of all standard tractor manufacturers.

Control units

Depending on the implement equipment

Pressure-free return flow

Do not exceed a back pressure of 5 bar.

5.11 Noise development data

The workplace-related emission sound pressure level
is lower than 70 dB(A), measured in operating
condition at the ear of the tractor driver with the cab
closed.

The emission sound pressure level mainly depends
on the vehicle used.

5.12 Drivable slope inclination

Across the slope

On left in direction of travel

15 %

On right in direction of travel

15 %

Up the slope and down the slope

Up the slope

15 %

Down the slope

15 %

CMS-T-00002296-C.1

CMS-T-00002297-E.1

5 | Technical data

Noise development data 

MG6659-EN-GB | F.1 | 25.10.2022 | © AMAZONE

42

Содержание Precea 3000-A







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды