Amazone GHS 1500 Drive SmartCut Скачать руководство пользователя страница 67

Страница: 67 / 138

Fasten the drawbar with the bolt

in one of the

holes

Tighten the bolts

and

with 210 Nm.

CMS-I-00003722

6.5 Preparing the universal joint shaft

Have the length of the universal joint shaft
adjusted by a specialist workshop.

Have the universal joint shaft installed by a
specialist workshop.

6.6 Installing the universal joint shaft on the implement

NOTE

The tractor symbol on the universal joint shaft
identifies the tractor-side connection.

Clean and grease the drive shaft on the
implement.

Make sure that the universal joint shaft guard is
functional.

Observe the universal joint shaft operating
manual.

Pull back the drawing sleeve

Push the universal joint shaft

onto the drive

shaft until the lock engages.

CMS-I-00001041

CMS-T-00005128-A.1

CMS-T-00001665-B.1

6 | Preparing the machine

Preparing the universal joint shaft

MG6212-EN-II | C.1 | 12.04.2021

Содержание GHS 1500 Drive SmartCut











































































































































Результаты поиска

Содержание GHS 1500 Drive SmartCut

Отзывы:

Бренды по названию

Популярные бренды

Amazone GHS 1500 Drive SmartCut, Оригинальное руководство по эксплуатации

Результаты поиска

Содержание GHS 1500 Drive SmartCut

Отзывы:

Бренды по названию

Популярные бренды