8
ENGLISH
9
ENGLISH
TROUBLESHOOTING
CONTINUED NEXT PAGE
MAINTENANCE
Warning: Failure to properly maintain your shredder will void the warranty.
Oil the shredder blades every month with basic vegetable, cooking oil or shredder oil. Follow oiling
procedure below (FIGURE 3). It helps to keep the shredder blades operating well over many years of
use.
Oiling procedure:
1. Turn off shredder.
2. Apply shredder oil across paper entry.
3. Turn shredder in reverse mode for 3~5 seconds.
•
Do not spray or keep any aerosol products
in or around shredder.
•
DO NOT USE CANNED AIR ON SHREDDER.
CLEANING:
• ALWAYS UNPLUG THE SHREDDER BEFORE CLEANING!
• Only clean the shredder by carefully wiping the unit with a dry soft cloth or towel.
• Do not clean or immerse shredder in water. Having the unit wet may result in damage or malfunction to
the electrical components. If the shredder happens to get wet, be sure to completely dry the unit immedi-
ately with a cloth or towel.
• Never use anything flammable to clean the shredder. This may result in serious injury or damage to the product.
FIGURE 3
Shredder
Oil
DO NOT USE
AEROSOL PRODUCTS!
!
Caution:
If there is a problem with your shredder, check below for the symptoms and steps to resolve. If you
continue to have problems, contact customer support at our Service Center.
DO NOT ATTEMPT TO
REPAIR BY OPENING THE SHREDDER HEAD. This will completely void the product warranty.
The shredder does not work at all.
1)
Make sure the unit is
plugged in
and that the outlet is in good working order.
2)
Overheating with extended use:
In the event that the shredder has shred continuously
beyond the maximum running time and overheated, the unit will automatically shut off. If this hap-
pens,
switch the shredder off for 45 minutes
or longer before resuming normal operation.
3)
Shredders with pull-out wastebaskets feature a safety power cut off upon bin removal. Shredder will
not function unless the pull-out wastebasket is pushed in all the way and properly set back into place
4)
If using a plastic bag to line the wastebasket, please remove it. This may cause the shredder not to
operate properly.
5)
The activation sensor of the shredder is located near the center of the feed slot. Be sure to feed
directly into the center area to activate the machine (especially applies to smaller pieces of paper
or credit cards).
The shredder runs in “Rev (Reverse)” mode but not in “Auto (On)” mode.
While in “Auto” mode, the motor will not start running until paper is inserted into the feed slot. Set the
unit to “Auto” and insert paper to shred. The sensor that activates the shredder in Auto mode is located
directly in the center of the slot. If the paper you are inserting is narrow, it may not be activating the
optical sensor. It is also possible that the feed slot has become blocked with paper. Insert an index card
or any rigid sheet of cardstock (old greeting card or folded file folder), directly in the center of the feed
slot, while applying force to help push the jammed paper through. This will usually clear any paper
blockage.
How to clear a paper jam in the shredder.
1)
Switch the shredder over into Reverse (REV) mode. While in Reverse, the shredder will back up and
loosen the jammed paper. If required, you may need to tug and remove several sheets to effectively
clear the machine. When jammed paper is loosened or removed, switch back to the Auto-On mode
to continue shredding. Repeat steps if needed.
2)
With stubborn situations where the reverse function does not help, you may loosen the jammed
paper with shredder oil (cooking oil is acceptable, nothing aerosol). Start by drizzling oil into the
feed slot where the paper is jammed. Let it soak for about 30 minutes to completely saturate. Return
