Amatrol 890-FTS1 Скачать руководство пользователя страница 1

Страница: 1 / 12

L17401-CL06JEN-E2-S02, REV. C INTRODUCTION TO TROUBLESHOOTING
Copyright © 2019 Amatrol, Inc.

S02-1

SKILL 2

TEST A MANUAL SWITCH

Procedure Overview

In this procedure, you will test the operation of a pushbutton switch and a

selector switch. To do this, you will insert faults into each component using the
890-FTS1 Troubleshooting System or manual fault plugs.



1. Perform a lockout/tagout on the safety switch of the 85-MT5.

NOTE

If you are using manual fault insertion, skip to step 3.



2. Perform the following substeps to set up the 890-FTS1 Troubleshooting

System with a power cord.

A. Make sure the troubleshooting system is plugged into a wall outlet.

B. Make sure the troubleshooting system is turned off.

C. Locate the fault terminals at the rear of the Operator Station on the 85-MT5

trainer.

D. Make sure that the fault cables are connected to the 85-MT5 Operator

Station panel in the standard confi guration as shown on the back of the
Operator Station panel and in fi gure 2-1.

OPERATOR STATION FAULT CONNECTION TABLE

Fault Cable Number

Connected to Station

Fault Terminal

Содержание 890-FTS1













Результаты поиска

Содержание 890-FTS1

Отзывы:

Похожие инструкции для 890-FTS1

Бренды по названию

Популярные бренды

Amatrol 890-FTS1, Руководство пользователя

Результаты поиска

Содержание 890-FTS1

Отзывы:

Похожие инструкции для 890-FTS1

Бренды по названию

Популярные бренды