Amano Time Guardian FRT-40 Скачать руководство пользователя страница 76

Страница: 76 / 93

FPT-40 Fingerprint Terminal Installation & Operation Guide

Page 3-9

Replacing Optical Sensor Lens

To replace the optical sensor lens:

1. If optical sensor lens becomes damaged (scratched) and cannot be

cleaned, replacement may be necessary.

2. Use the replacement [spare] optical sensor lens included with the

terminal. Remove the spare sensor lens from the protective
packaging (see figure), using care not to touch the prism.

3-12

Spare Prism & Packaging

3. Disconnect the AC Power Adapter from the bottom of the terminal.

4. Disconnect the communication cable (either Ethernet or serial DB9

connector)

5. Loosen and remove the four (4) back plate retaining screws and

remove the terminal from the wall mounted back plate.

6. Place the terminal on a soft surface face down. Located and remove

the four (4) Phillips Head screws holding the case front cover. There
will be one screw in each corner on the back of the case.

7. After removing the screws, place the terminal right-side up on the

back of the case and VERY CAREFULLY lift the front cover up.

8. The sensor housing must be removed by unscrewing the four (4)

Phillips head screws holding it down to access the optical sensor
lens (see figure).

Prism

Содержание Time Guardian FRT-40






























































































Результаты поиска

Содержание Time Guardian FRT-40

Отзывы:

Amano Time Guardian FRT-40, Руководство пользователя, Страница: 76 / 93

Результаты поиска

Содержание Time Guardian FRT-40

Отзывы: