Amano Time Guardian FRT-40 Скачать руководство пользователя страница 11

Страница: 11 / 93

Page 1-6

FPT-40 Fingerprint Terminal Installation & Operation Guide

Once a mounting location has been chosen, perform the following:

1. Loosen and remove the four (4) back plate retaining screws to

remove the back plate as shown (see

Figure 1-2

). Set the FPT-40

terminal face up on a flat surface.

Figure 1-2 Back Plate For Wall Mounting

2. Using the back plate as a template, mark the location of the upper

mounting holes on the wall. Mark a vertical line on the wall as a guide
to align the lower mounting holes.

Note:

Pay attention to the orientation. The back plate should only be

mounted one-way as it is keyed to fit into the back of the
fingerprint reader.

3. Install a screw or anchor at the mark and hang the back plate from the

top-mounting holes. Level the back plate by centering the vertical line
in the bottom holes.

4. Mark the location of the bottom holes.

5. Install the screws or anchors for the bottom-mounting holes and

secure the back plate to the wall.

6. Insert the back of the fingerprint reader onto the four (4) retaining

tabs. The tabs are keyed to accept the fingerprint reader only one
way! Secure the reader to the tabs by inserting and tightening the 4
retaining screws.

7. Your fingerprint reader is now mounted to the wall and ready to

connect the data and power lines. After wall mounting, remove the
dustproof film on the sensor window. Proceed to the next section,

Communication Connections

Содержание Time Guardian FRT-40






























































































Результаты поиска

Содержание Time Guardian FRT-40

Отзывы:

Amano Time Guardian FRT-40, Руководство пользователя, Страница: 11 / 93

Результаты поиска

Содержание Time Guardian FRT-40

Отзывы: