Amana 18 Cu. Ft Скачать руководство пользователя страница 64

Страница: 64 / 72

RS1200004 Rev. 0

C–12

Door Buckets

Door buckets adjust to meet individual storage needs.

• Remove door buckets by pushing tabs on both

sides of shelves toward center and pulling bucket
out.

• Replace door buckets by sliding in until tabs lock

into place.

A Tabs

Tall Package Retainer (some models)

Tall package retainer keeps tall items secure. Retainer fits
on front edge of any refrigerator door bucket or door shelf.

A Tabs

Door Shelves

• Remove door shelves by lifting ends and pulling

out.

• Replace door shelves by placing shelf on glides and

sliding down.

A Glide

Adjustable Divider (some models)

Adjustable divider keeps items in place and adjusts to
meet individual storage needs. Divider fits in any door
bucket or door shelf.

Bottle Holder (some models)

Bottle holder keeps items in place and adjusts to meet
individual storage needs. Bottle holder fits in any door
bucket or door shelf.

Содержание 18 Cu. Ft









































































Результаты поиска

Содержание 18 Cu. Ft

Отзывы:

Amana 18 Cu. Ft, Сервисная инструкция, Страница: 64 / 72

Результаты поиска

Содержание 18 Cu. Ft

Отзывы: