Amana 18 Cu. Ft Скачать руководство пользователя страница 63

Страница: 63 / 72

C–11

RS1200004 Rev. 0

Storage Rack (some models)

Storage rack provides convenient storage for a large
bottle, eggs, etc.

• Hang rack by hooking over side of shelf.

A Bottle rack

Covered Storage Bucket (some models)

The covered storage bucket has a lid and removable egg
tray. When tray is removed, bucket will accept standard
egg carton, ice, etc.

Dairy Center (some models)

The dairy center provides convenient storage for butter,
cheese, etc.

• Remove dairy center by lifting door, pushing tabs of

shelf down on both sides, and pulling out.

• Replace dairy center by sliding in until tabs lock

into place, then lower door.

A Door

B Tab

Replace shelf by inserting hooks into metal track and
lowering the front. Use slots 4 though 6 only.

Replace drawer by sliding in. Make sure boot fits
snugly over air inlet in back wall.

1 Chiller Fresh System installed on left side of refrig-

erator.

2 Chiller Fresh System installed on right side of refrig-

erator.

A Air inlet

C Plastic cap

B Boot

D Metal rack

Содержание 18 Cu. Ft









































































Результаты поиска

Содержание 18 Cu. Ft

Отзывы:

Amana 18 Cu. Ft, Сервисная инструкция, Страница: 63 / 72

Результаты поиска

Содержание 18 Cu. Ft

Отзывы: