Amana 18 Cu. Ft Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 72

Amana 18 Cu. Ft Скачать руководство пользователя страница 61

C–9

RS1200004 Rev. 0

Fresh Food Features

Fresh Food Shelves

Shelves adjust to meet individual storage needs. Some
models feature Spillsaver

TM

Shelves and Easy Glide

TM

shelves. Spillsaver

TM

Shelves hold minor spills for easier

cleaning.

Controls

This refrigerator is designed to operate at normal
household temperatures of 55° to 110°F (13° to 43°C).

Fresh Food and Deepfreeze® Controls

Fresh Food control is located on upper rear wall of Fresh
Food section.

4

5

6

7

3

2

1

Deepfreeze® control is located on left front ceiling of
freezer section.

4

Deepfreeze Control

Cold

Coldest

Setting Controls

When Deepfreeze® control is set to

OFF, neither

refrigerator nor freezer sections will cool. Initially, set
both controls to

4. Wait 24 hours for refrigerator and

freezer sections to stabilize temperatures. After 24 hours,
adjust controls, one number at a time, as desired. One is
warmest setting and seven is coldest.

Set controls precisely using a household thermometer
with a temperature range between -5° to 50°F
(-21° to 10°C).

Put thermometer snugly between frozen packages in
freezer section. Wait 5–8 hours. If Deepfreeze®
temperature is not 0° to 2°F (-17° to -16°C), adjust
Deepfreeze® control one number at a time. Check again
after 5–8 hours.

Put thermometer in a glass of water in middle of Fresh
Food section. Wait 5–8 hours. If Fresh Food temperature
is not 38° to 40°F (3° to 4°C), adjust Fresh Food control
one number at a time. Check again after 5–8 hours.

CAUTION

!

Make sure shelf is secure before replacing items on
shelf to avoid property damage.

CAUTION

!

Handle tempered glass shelves carefully to avoid
personal injury or property damage. Shelves may
break suddenly if nicked, scratched, or exposed to
sudden temperature change.

• Remove shelves by lifting up shelf front, releasing

hooks from metal track, then pulling out.

• Replace shelves by inserting hooks into metal track

and lowering front of shelf.

A

B

C

A Shelf

C Hook

B Metal rack

Easy Glide

TM

shelves pull forward for easy access to

items in back.

«
...
59
60
61
62
63
...
»

Содержание 18 Cu. Ft









































































Отзывы:

Нет отзывов