Amana 18 Cu. Ft Скачать руководство пользователя страница 60

Страница: 60 / 72

RS1200004 Rev. 0

C–8

Installation Checklist

This checklist is for personal records only.

Consumer

Installer

Doors

Handles are solidly attached to doors.

Handle side of door is

" (3 mm) higher than hinge side. (Door lowers when

loaded with food.)

Doors seal completely to refrigerator cabinet.

Leveling

Refrigerator is tilted

" (6 mm) from front to rear.

Toe grille is properly attached to refrigerator.

Ice Maker

Water supply to refrigerator is turned on.

Water leaks are not present at connection between household water supply and
refrigerator. (After 24 hours, consumer should check connection for water leaks.)

Ice maker arm is in

on position for ice production. (It may take up to 24 hours for

first harvest of ice.)

Product Literature

Owner's manual is reviewed including the following information.

• product registration card
• Fresh Food and Deepfreeze® controls
• Humidity-controlled crispers
• normal operating sounds

Notes

Consumer's Signature

Date

Installer's Company Name/Phone Number

Installer's Signature

Содержание 18 Cu. Ft









































































Результаты поиска

Содержание 18 Cu. Ft

Отзывы:

Amana 18 Cu. Ft, Сервисная инструкция, Страница: 60 / 72

Результаты поиска

Содержание 18 Cu. Ft

Отзывы: