Amana 18 Cu. Ft Скачать руководство пользователя страница 59

Страница: 59 / 72

C–7

RS1200004 Rev. 0

Leveling Refrigerator

CAUTION

Protect soft vinyl or other flooring with cardboard, rugs
or other protective material to avoid property damage.

If your refrigerator requires an ice maker water supply
connection, proceed to

Connect ice maker water supply

section before leveling your refrigerator.
1.

Plug in power cord.

Move refrigerator into final location.

Level refrigerator using a level placed on top of the
refrigerator.

• Remove toe grille. Remove bottom hinge cover if

refrigerator has a stabilizing leg.

• Turn roller adjustment screws to raise or lower

refrigerator cabinet. Front of refrigerator must be
¼" (6 mm), or ½ bubble on your level, higher than
the back of your refrigerator.

• Make sure refrigerator cabinet is level from side to

side by adjusting left and right roller adjustment
screw

(A).

• Turn stabilizing leg

(C–some models) clockwise

until firmly against floor.

Replace toe grille

(D) and bottom hinge cover(B). See

markings on inside of toe grille to insure proper
placement.

• Snap top portion into place first. Press down on

lower part of grille until bottom portion snaps into
place.

A Roller adjustment screw

D Toe grille

B Bottom hinge cover
C Stabilizing leg (some models)

Review

Installation Checklist in Owner's Manual with

consumer.

Содержание 18 Cu. Ft









































































Результаты поиска

Содержание 18 Cu. Ft

Отзывы:

Amana 18 Cu. Ft, Сервисная инструкция, Страница: 59 / 72

Результаты поиска

Содержание 18 Cu. Ft

Отзывы: