Amana 18 Cu. Ft, Сервисная инструкция, Страница: 57 / 72

C–5 RS1200004 Rev. 0
Reverse Handles (front-mounted design)
1.
Remove handle screw from top handle trim (A). Pry
up edge of handle trim on both ends of handle using a
putty knife with the blade covered with masking tape.
Remove handle
(C) from door by removing 1
remaining mounting screw at each end of handle.
To Reverse Doors
Service Notice: Contour Door Models Only
Only a qualified servicer can reverse this door. To have
doors reversed, please call 1-800-843-0304. There is a fee
for this service.
For Non-Contour Door Models
•
Remove bottom hinge (A) and shim(C) with 3 /
8
" hex nut
driver. Remove hinge pin
(B). Remove and retain all
round washer shims
(D), if present.
C
A
B
D
Reverse Hinges
1.
Transfer three cabinet plugs from top corner of
cabinet to holes left from top hinge removal.
2. Transfer three 5 /
16
" hex head screws opposite center
hinge area to the holes left by center hinge removal.
3. Transfer all hinges and shims to opposite side of
cabinet.
• Replace bottom hinge pin (A) in bottom hinge
bracket (C) in hole(B) outside of cabinet, along with
all washer shims retained from hinge removal.
C
A
B
• Install top hinge screws loosely to allow enough
clearance to reinstall door.
IMPORTANT: To avoid damage to interior finish, remove
buckets and shelves from freezer and refrigerator door
before continuing door reversal. Lay doors interior-side
down on carpet, or a table or floor protected with blankets
or towels.
Remove Door Stop
1. Unscrew 2 Phillips screws and remove door stop
(B)
from refrigerator and freezer door (A). Retain all screws
for door stop replacement.
A
B
Reverse Handles (side-mounted design)
To reverse handles on contour model, see service notice
at top of page.
2. Remove 1 plug from top hinge side of door and 2 from
front hinge side of door. Replace 3 plugs in empty
mounting holes.
3. Mount refrigerator handle on opposite side of door
using mounting screws removed in previous step.
4. Snap handle trim into place and replace screw at top
of handle.
A
B
C
D
A
E
A Handle trim D Screw
B Name plate E Plugs
C Handle
5. Open freezer door 90°. Locate two notches on back
of freezer handle. Insert flat screwdriver driver blade
or putty knife blade wrapped in masking tape. Pry up
back edge of handle cap and remove from handle.
6. Remove handle from door by removing two mounting
screws.
7. Remove 2 plugs from opposite side of freezer door
and replace in empty mounting holes.
8. Mount freezer handle to opposite side of door using
mounting screws removed in previous step.
9. Angle front edge of handle cap downward toward back
lip of freezer handle. Verify bottom tab on freezer cap
slides under rear lip of freezer handle. Snap rear edge
of handle cap in place.
B
C
D
A
A Freezer handle C Screws
B Handle cap D Plugs
Remove Door Stop
1. Mount door stop opposite handle side on underside of
door.
To Replace Doors
1. Place freezer door on bottom hinge pin.
2. Replace center hinge pin with hex nut driver. Make
sure fit is tight. Replace round shims and door
closure.
3. Replace top hinge and shims, but allow enough
clearance to slide hinge side of refrigerator door into
place. Tighten down top hinge to securely hold door.
4. Use a dime at top to space door 11 /
16
"(18 mm)from
cabinet.
5. Handle side of door should be approximately 1 /
8
" (3
mm) higher than hinge side. Door will become level
when it is loaded with food.