Amana 18 Cu. Ft Скачать руководство пользователя страница 45

Страница: 45 / 72

B - 3

RS1200004 Rev. 0

Door
shim

Center
hinge pin

Hinge
shims

Center hinge
bracket

Screws

Center Hinge Nomenclature

Pull tape off freezer door and lift door off unit. Set
door on a padded surface to prevent damage to
finish.

If clearance requirements so dictate, remove center
and lower door hinges:

A. Use No. 2 Phillips screwdriver to remove 3

screws from center hinge bracket. Remove and
retain bracket, screws, and all shims.

B. Remove toe grille by pulling it directly away from

unit, and pop plastic cap off bottom hinge.

NOTE: Grille and cover are fragile: keep both parts safe

from harm.

Toe grille

Bottom
hinge cap

Brake foot

Bottom
hinge bracket

Button
plug

Bottom
hinge pin

Shim

Screws

Bottom Hinge Nomenclature

C. Remove bottom hinge pin and all shims from

bottom hinge bracket. Note number of shims.
Retain all parts.

D. With 3/8" nut driver, loosen 3 mounting screws

from bottom hinge bracket. Remove and retain
bracket and screws.

Situate the unit

Wrap refrigerator carefully with blanket or appliance
pad. Slide appliance cart under side of unit. Thread
cart strap around refrigerator and tighten strap.

Move refrigerator in front of final location. Remove
cart strap, cart and padding.

You must decide what to do next.

•

If door reversal is called for, skip to Door
Reversal or (if unit has contour doors) to Contour
Door Reversal.

•

If door reversal is not called for and unit has an
icemaker, perform Step 4 and then skip to Water
Supply.

•

If door reversal is not called for and unit has no
icemaker, perform Step 4 and then skip to Final
Steps.

Rehang doors by reversing removal procedure.

Installation Instructions

Содержание 18 Cu. Ft









































































Результаты поиска

Содержание 18 Cu. Ft

Отзывы:

Amana 18 Cu. Ft, Сервисная инструкция, Страница: 45 / 72

Результаты поиска

Содержание 18 Cu. Ft

Отзывы: