manualshive.com logo in svg

Amana 18 Cu. Ft, Сервисная инструкция, Страница: 44 / 72

Поделиться
Скачать
Amana 18 Cu. Ft Скачать руководство пользователя страница 44

RS1200004   Rev. 0

B - 2

This refrigerator operates most efficiently when it is
properly installed. Amana cannot be responsible for loss,
injury or damage caused by improper installation or
unqualified personnel.

!

WARNING

To minimize risk of death, personal injury and/or
property damage, read and heed all safety messages.

Unpack unit

1.

Cut wires at top and bottom of crate. Remove and
discard both wires and lid. Retain Styrofoam pads.

2.

Being careful not to damage finish, cut crate apart at
corners, pull it off unit and discard the pieces.

NOTE: When performing the next step remember that

the machine compartment cover will not bear
the weight of the unit.

3.

Lay two Styrofoam pads (retained in Step 1) on floor
behind refrigerator. Arrange pads so that, when unit
lays on its back, it will rest on pads – one pad at a
point just above the machine compartment cover
and the other at a point just below the top of the unit.

To minimize risk of personal injury and/or property
damage, get someone to help lift the refrigerator
before attempting steps 4-6.

!

CAUTION

4.

Tip the refrigerator backward and lower it gently so
that it lays on pads placed in Step 3.

5.

On bottom of unit, use a 7/16" wrench to remove
bolts that hold pallet to unit. Discard bolts and pallet.

To avoid property damage, don't leave unit lying on its
back any longer than is absolutely necessary.

!

CAUTION

6.

Lift refrigerator back into upright position. Remove
and discard cardboard from between doors.

To avoid risk of electrical shock that can cause death
or severe personal injury, disconnect unit from power
before removing doors. Connect to power only after 
doors are replaced.

!

WARNING

Remove doors if necessary

1.

Open both compartment doors. Remove door
buckets, all shelving and drawers from refrigerator
and freezer compartments. Place components on a
padded surface to avoid damage.

2.

Close both doors and tape them shut so they don’t
fall off unexpectedly when hinges are removed.

To reduce risk of death, severe personal injury and/or
property damage due to falling objects, always tape
doors shut before hinges are removed.

!

WARNING

3.

On top of unit, remove and retain plastic cap from
door hinge.

Posi-Pin shim

Top hinge shim

Top hinge

Screws

Plastic cap

4.

Removal of plastic cap exposes top hinge and the 3
screws that secure it. With 5/16" nut driver, remove
and retain screws and top door hinge. Leave Posi-
Pin shim in place.

5.

Pull tape off door and lift door off unit. Set door on
padded surface to prevent damage to finish.

6.

With 5/16" nut driver (some units require a 9/32" nut
driver), remove and retain center hinge pin and all
shims. Note number and location of shims (above or
below hinge) as you do so.

Installation Instructions

Содержание 18 Cu. Ft









































































Отзывы:

Нет отзывов