Amana 18 Cu. Ft Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 72

Amana 18 Cu. Ft Скачать руководство пользователя страница 36

RS120004 Rev. 0

A - 4

Fill Cup

Remove module and support assembly. Remove
ejector blades and shut-off arm. Pull fill cup from
mold.

Ejector Blades or Stripper

Remove module and support assembly. When rein-
stalling ejector blades, realign "D" coupling with mod-
ule cam.

Accessing Control box

To remove motor and contact assembly from control box,
take out three screws (arrows) and pull free after discon-
necting shut-off arm.

To avoid damange to main assembly, do not rotate
blades or drive gear.

There are several switches which will jam if manually
turned counterclockwise and gears will be destroyed if
turned clockwise. To advance the ice maker into the
cycle, use a jumper to bridge

H

to

R

and unless the

motor is defective, it will run. (The shut-off arm must
be in the on position.)

NOTE:

There are several slotted shafts on the motor
assembly board. Do not under any circum
stances insert a screwdriver and attempt to
turn these shafts. The slots are to permit as
sembly only.

NOTE:

There are not repairable or replaceable
components in the module. Unless you are
replacing the module, there should be no need
to remove it when diagnosing or repairing the
ice maker.

Water valve

energized

7.5 seconds

140cc fill

about 11:00

o'clock

Ejector blade stop position

(about 1:30 o'clock

Start position:

thermostat closes,

motor on,
heater on

Ejector stall on ice,

Motor on (30 seconds

to 5 minutes) about

4:00 o'clock

6:00 o'clock

position

Thermostat

opens in this

range of

rotation then

heater is off

Ice Maker

CAUTION

!

Remove appropriate
fill cup slot .

Forcefully pull cup up
and out of slot .

Mold and Heater Screw Access Ports

«
...
34
35
36
37
38
...
»

Содержание 18 Cu. Ft









































































Отзывы:

Нет отзывов