manualshive.com logo in svg

Amana 18 Cu. Ft, Сервисная инструкция, Страница: 32 / 72

Поделиться
Скачать
Amana 18 Cu. Ft Скачать руководство пользователя страница 32

RS1200004   Rev. 0

32

Disassembly Procedures

!

WARNING

To avoid risk of electrical shock, personal injury, or death, disconnect electrical power source to unit, unless test
procedures require power to be connected. Discharge capacitor through a resistor before attempting to service.
Ensure all ground wires are connected before certifying unit as repaired and/or operational.

Overload/Relay

1. Remove heat exchanger cover, condenser fan grille

and machine compartment cover.

2. Discharge capacitor (if unit is so equipped) through a

10.000-ohm resistor.

3. Using fingers and standard screwdriver, press and

pry bale strap off the overload/relay cover.

4. Remove cover to access overload/relay components.

Compressor

1. Remove heat exchanger cover, machine.

compartment cover and condenser fan grille.

2. Remove drier.
3. Disconnect all compressor wiring.
4. Unbraze low and high pressure lines at compressor.
5.  Remove compressor mounting bolts.
6. Lift compressor out of unit.

NOTE:

Install new drier and compressor per

instructions in “Service Procedures.” Evacuate
and recharge sealed system per instructions in
“Service Procedures.”

Condenser Removal

NOTE:

Condenser and machine tray are a 1 piece

assembly and must be replaced as a unit.

1. Under front of unit, remove toe grille, defrost timer

and timer box.

2. From backside of unit, remove heat exchanger cover,

machine compartment cover and condenser fan
grille.

3. Remove condenser fan and mounting plate.
4. Remove drier and compressor.
5. Disconnect all cabinet wiring from machine tray.
6. Reach in the machine compartment from the rear and

pull machine compartment tray with condenser out
the back of unit.

Содержание 18 Cu. Ft









































































Отзывы:

Нет отзывов