manualshive.com logo in svg

Alvarion BreezeMAX PRO-S CPE, Руководство по эксплуатации продукта

Поделиться
Скачать
Alvarion BreezeMAX PRO-S CPE Скачать руководство пользователя страница 69

Installing the 3.5 GHz Detached Antenna

BreezeMAX CPEs Product Manual 

47

2.4.3

Window Mounting the 3.5 GHz Detached 

Antenna, with Rotation Capability

The installation kit includes the following: 4 PHK40*16PT screws (1), 2 M4 
washers (2), 2 rotation bars (3) and 2 suction cups (4).

1

Attach the rotation bars to the antenna and the suction cups to the rotation 
bars. Refer to 

Figure 2-17

 for directions. 

2

Determine the location of the antenna on the glass. Attach it to the window by 
pressing the suction cups onto the glass.

3

Connect the antenna cable to the connector located on the bottom side of the 
antenna. Use only the torque key supplied with the antenna. Do not over 
tighten. Do not use a wrench or a similar tightening tool.

4

Rotate the antenna left or right so the domed surface of the antenna is facing 
the direction of the Base Station. Check the received Signal LEDs to ensure 
the antenna is aimed correctly. 

Содержание BreezeMAX PRO-S CPE



































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды