Alvarado CLST-3 Скачать руководство пользователя

Страница: 41 / 46

MST Installation Instructions

Installation Instructions [email protected] +1(909) 591-8431 www.alvaradomfg.com

Page 41

Appendix E -

Fail-lock / Fail-safe Spring and Solenoid Configurations (Cont)

Fail-safe

Fail-lock

Clockwise

Fail-lock / Fail-safe Spring and Solenoid Configurations - Fixed

Solenoid

NOTE

For use with turnstiles that utilize fixed solenoid mounting positions.

Spring Configuration

Solenoid Mount Position

A - Return Spring
B - Solenoid

Spring

CW Lock

Arm

Fail-safe

Solenoid

(Black)

(Red)

Fail-lock

Solenoid

CW Lock

Arm

A - Return Spring
B - Solenoid

Spring

(Black)

(Silver)

Spring Configuration

Solenoid Mount Position (use holes 1 & 3)

NOTES

Bend lock arm tabs to mechanically adjust spring tension.
Solenoid mounting screws must be tightened to 30 in-lbs.

to avoid slippage from continuous use.

Increase

spring

tension

Decrease

spring

tension

Increase

spring

tension

Decrease

spring

tension

Содержание CLST-3















































Результаты поиска

Содержание CLST-3

Отзывы:

Похожие инструкции для CLST-3

Бренды по названию

Популярные бренды

Alvarado CLST-3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CLST-3

Отзывы:

Похожие инструкции для CLST-3

Бренды по названию

Популярные бренды