background image

MST Installation Instructions

Installation Instructions                [email protected]   +1(909) 591-8431    www.alvaradomfg.com

 

 

Page 21

SW4 DIP Switch Descriptions

Sets solenoid control for the Clockwise direction in fail lock 

configuration. Power is applied to solenoid upon activation 

signal to release lock arm for rotation.

CWFL

FS

Sets solenoid control for the Clockwise direction in fail 

safe configuration. Power is applied to solenoid for locked 

condition and removed upon activation signal to release lock 

arm for rotation.

Sets solenoid control for the Counter Clockwise direction 

in fail lock configuration. Power is applied to solenoid upon 

activation signal to release lock arm for rotation. 

CCWFL FS

Sets solenoid control for the Counter Clockwise direction 

in fail safe configuration. Power is applied to solenoid for 

locked condition and removed upon activation signal to 

release lock arm for rotation. 

Adjusts automatic re-lock timing. See Figure 28A for 

settings.

T3

T3ON

Adjusts automatic re-lock timing. See Figure 28A for 

settings.

Adjusts automatic re-lock timing. See Figure 28A for 

settings.

T4

T4ON

Adjusts automatic re-lock timing. See Figure 28A for 

settings. 

Sets Length of time of contact closure on CNT and COM 

feedback to 100ms. 

100

FBPL

Sets Length of time of contact closure on CNT and COM 

feedback to 300ms.

Set switch to left when using Red/Yellow/Green Activation 

Lights.

JS3

JS2

Set switch to right when using Red/Green Activation Lights.

Sets operation to standard optical sensor configuration for 

passage feedback after second sensor detection. 

STD

ROFP

Sets operation to custom optical sensor configuration for 

passage feedback on first sensor detection.

Configures OPN terminals as normally open (N.O.). 

 

OPN inputs are used for fire alarm / free passage modes.

AUX

AUX

Configures OPN terminals as normally closed (N.C.). 

 

OPN inputs are used for fire alarm / free passage modes.

SW4 Layout 

(Figure 29A)

LEFT / OFF

Switch 

Position

Switch 

Position

RIGHT / ON

 

Содержание CLST-3















































Отзывы:

Похожие инструкции для CLST-3