RE611P
Indoor Motion Sensor, Pet Immune, Encrypted
1.
Specifications
Frequency:
433.92 MHz
Operating Temperature:
32°-120°F (0°-49°C)
Operating Humidity:
5-95% RH non-condensing
Battery:
1x CR123A Panasonic Lithium 3V DC
Battery Life:
5 Years
Compatibility:
Encrypted
Pet Immunity:
Up to a maximum of 85 lbs
Supervisory Interval:
Approximately 60 minutes
Coverage Area:
40 feet by 40 feet, 90° angle
Light Immunity:
2000 Lux
Coverage Pattern:
Side View:
Top View:
2.
Package Contents
1x Sensor
1x Sensitivity Jumper
4x Screws & Wall Anchor 1x CR123A battery (installed)
2x Sensor Case Screw
1x Back Mounting 2-Sided Adhesive Tape
1x Manual
2x Side Mounting 2-Sided Adhesive Tape
3.
Component Identification
4.
Enrollment:
To enroll the motion sensor, set your panel into programming mode according
to the panel manufacturer’s instruction. When prompted by the panel, enter
the 6-digit serial number printed on the sensor label.
Some panels can enroll your sensor by capturing the serial number
transmitted by your sensor. The sensor can be enrolled in the panel or
recognized by the DSC wireless device programmer device by triggering
wireless transmissions. The red LED will begin to flash for 45 seconds. When
the LED stops flashing, the sensor can be triggered by waving your hand in
front of the motion sensor. The sensor will transmit every time motion is
detected. Trigger the motion sensor as many times as necessary until the
panel recognizes the sensor’s serial number.
5.
Mounting
Mount the motion sensor at 7.5 feet (2.3
meters) above the floor. Press the case release
button to separate the front and back sensor
case. The back case gives access to both the
flush mount and corner mount screw knock
outs. Remove the appropriate knockouts and
use the included screws to mount in the
desired mounting location. It is recommended
to ensure there is a tight seal around the
knockouts to prevent bugs from entering the
sensor and causing false alarms. Replace the
front sensor cover to snap shut and screw in
the sensor case screws on the top and bottom
of the back sensor case. The RE611P is intended to be installed in
accordance with the Standard for Installation and Classification of
Residential Burglar Alarm Systems, UL1641 & UL 691 - Classification of
Burglar and Holdup Alarm Systems, UL 681, and is it intended for
Residential use only. The RE611P intrusion detection unit shall be installed
in accordance with the Standard for Installation and Classification of
Residential Burglar Alarm Systems, CAN/ULC-S310 and CSA C22.1,
Canadian Electrical Code, Part I, Safety Standard for Electrical Installations.
6.
Sensitivity Jumper Settings
For standard sensitivity motion detection with pet immunity leave the jumper
in the default setting (on). Remove the jumper if increased sensitivity to
movement is desired.
7.
Walk Test Mode
Walk test mode can be used to test the motion sensor detection coverage
area. To enter walk-test mode remove the battery for 10 seconds and
re-insert the battery. The red LED will begin to flash indicating that the motion
sensor is warming up. After 45 seconds, the LED will stop flashing which
indicates the motion sensor is ready to detect motion. The LED will illuminate
each time motion is detected. Once the LED goes out, the sensor is ready to
detect motion again. Walk test mode ends after 15 minutes. It is
recommended that the RE611P PIR is tested monthly to ensure proper
function.
7.5 ft
0 3 6 10 13 16 19 23 26 29 33 36 40
(feet)
29 26 23 19 16 13 9 6 3 0 3 6 9 13 16 19 23 26 29
0
3
6
10
13
16
19
23
26
29
33
36
40
0
3
6
10
13
16
19
23
26
29
33
36
40
Tamper Switch
Sensitivity Jumper
CR123A Battery
Case Release Button
Sensor Case Screws
(feet)
(feet
)
