Altuscn KM0032 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 155

Altuscn KM0032 Скачать руководство пользователя страница 38

KM0032 / KM0532 / KM0932 User Manual

26

Daisy chained Installation Diagram

Network Administration

Once the KM0032 / KM0532 / KM0932’s network settings have been
configured from a local console (see

Network Configuration

, page 29), for

convenience, administrative tasks can be performed remotely using a web
browser over the internet.

It is not necessary to connect cascaded switches to the network. Remote (over
the network) administration of cascaded switches are managed through the of
the first level switch.

Topology Considerations

The use of RJ-45 KVM port connectors, combined with Auto Signal
Compensation (ASC), allow signals to travel up to 300 meters (1000 feet) and
still maintain reliability and high video resolution. This allows the KM0032 /
KM0532 / KM0932 installation to take advantage of the internal Cat 5e and Cat
6 wiring built-in to most modern commercial buildings.

Since the data signals are not transmitted in packets, the transmission cannot
go through network hubs or switches. Passive components such as patch
panels, keystone jacks, patch cables, etc. can be used to channel the traffic,
instead.

«
...
36
37
38
39
40
...
»

Содержание KM0032




























































































































































Отзывы:

Нет отзывов