Altuscn KM0032 Скачать руководство пользователя страница 111

Страница: 111 / 155

Chapter 10

Maintenance

Overview

The Maintenance tab offers two menu items:

Backup/Restore

, and

Firmware

Upgrade

Backup/Restore allows super administrators to backup KM0032 /
KM0532 / KM0932 system configuration settings to a file, and restore
configuration settings from previously saved files.

Firmware Upgrade allows super administrators to upgrade firmware for
connected Matrix KVM Switches, attached console modules, and KVM
adapter cables.

Note:

Maintenance is only available from a browser session. The Backup/
Restore and Firmware Upgrade operations are not available from a
console session.

Backup / Restore

When you click the

Maintenance

tab, the Browser UI opens with the

Backup/

Restore

menu page displayed. The page is divided into two main sections:

Backup

, and

Restore

Содержание KM0032




























































































































































Результаты поиска

Содержание KM0032

Отзывы:

Altuscn KM0032, Руководство пользователя, Страница: 111 / 155

Результаты поиска

Содержание KM0032

Отзывы: