Pace1ST
- 1 -
Overview:
Pace1ST is a long range Ethernet transceiver designed for use with Pace1PRM, Pace4PRM,
Pace8PRM and Pace16PRM receivers. They transmit data at 100mbps full duplex and power via
Cat5e or higher cable in a PoE(+) compliant format. The Pace1ST will not deliver power to non-
compliant devices, thus avoiding damage to improperly connected non-PoE cameras/devices. The
receiver passes the PoE(+) compliant power over the cable to the Pace1ST transceiver which in
turn passes this power to an enabled IP camera/device. These plug and play units facilitate cost
effective solutions for IP devices that need to be installed at distances greater than 100m.
Features:
Rev. 111413
Installation Guide
Pace1ST
IP and PoE+ Over Extended Distance CAT5e
Agency Listings:
• UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
• CE European Conformity.
Input:
• PoE (15W) IEEE 802.3af compliant or
PoE+ (30W) IEEE 802.3at compliant
from Pace1PRM, Pace4PRM,
Pace8PRM, or Pace16PRM.
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5e.
• Speed: 10/100BaseT, half/full duplex,
auto negotiation.
PoE compliant to IEEE 802.3af (15W) and
PoE+ compliant to IEEE 802.3at (30W)
delivered to camera by Pace1ST.
• Throughput is rated to pass 100mbps of data.
CAT5e or Higher:
• Distance: up to 500m @ 100mbps.
LED Indicators:
• Green - PoE ON (by respective RJ45 jack).
• Yellow and Green LED IP Link status,
10/100Base-T/active.
Environmental:
•
Operating Temperature:
For 15W: --- 40ºC to 75ºC (--- 40ºF to 167ºF).
For 30W: --- 40ºC to 65ºC (--- 40ºF to 149ºF).
•
Storage Temperature:
--- 40ºC to 75ºC (--- 40ºF to 167ºF).
• Relative humidity:
20 to 85%, non-condensing.
Functions:
• Auto detection and protection of legacy
non-PoE cameras/devices.
Applications:
• Retrofit digital IP cameras in an analog
CCTV CAT5e installations.
• Extend Network link distance in an
industrial environment over 610m.
• Works with Megapixel, HD720, HD1080
and VGA (SD) cameras with proper
headend equipment.
Mechanical:
• Dimensions (W x L x H approx.):
2.27” x 2.645” x 1.12”
(57.66mm x 67.18mm x 28.44mm).
I.T.E. 43KC
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and
with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or
Recognized wire suitable for the application.
Pace1ST is not intended to be connected to outside plant leads and should be installed indoors
within the protected premises. Pace1ST is intended for indoor use only.
1. Secure unit to desired mounting surface with a proper fastening device utilizing the case’s
mounting hole (Fig. 2a, pg. 3). Unit should be mounted in the proximity of camera/device.
2. Connect structured cable from IP camera/device to RJ45 jack marked [PoE Out] (Fig. 2, pg. 3).
3. Connect CAT5e or higher to the connector marked [RJ45 IN] from receiver (Pace1PRM,
Pace4PRM, Pace8PRM or Pace16PRM) (Fig. 2, pg. 3).
Caution: once PoE connection is established between the receiver and Pace1ST, disconnection
from Pace1ST will not disable the PoE output voltage on the receiver. Although the Pace1ST can
be reconnected, caution should be taken not to connect the CAT5e wiring from the receiver to any
non-PoE device.
