Overview:
Pace1PRD is a long range Ethernet receiver which transmits data at 100Mbps full duplex
and power via a CAT5e or higher cable. The Pace1PRD receiver is powered via Altronix
NetWay1D midspan injector. The receiver passes the Hi-PoE (60W) power over the cable to the
eBridge200WPM transceiver which, in turn, passes this power to an enabled IP camera/device.
These plug and play units facilitate cost-effective solutions for IP devices that need to be installed
at distances greater than 100m.
Features:
Rev. 011615
Installation Guide
Pace1PRD
IP and Hi-PoE Receiver over extended distance CAT5e
Agency Listings:
• UL/cUL Listed for Information
Technology Equipment (UL 60950-1).
• CE European Conformity.
Input:
• Powered by NetWay1D (60W).
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5 structured cable.
• Distance: up to 500m.
• Speed: 10/100BaseT, half/full duplex,
auto negotiation.
• Throughput is rated to pass 100Mbps of
data at distances up to 500m.
With proper headend equipment this
supports
Megapixel, HD720, HD1080.
CAT5e or Higher:
• Distance: up to 500m @ 100Mbps
(see Cable Type, Total Device Power,
Data and Power Distance, pg. 3).
LED Indicators:
• Green - PoE ON (by respective RJ45 jack).
• Yellow and Green LED IP Link status,
10/100Base-T/active.
Environmental:
•
Operating Temperature:
– 20ºC to 49ºC (– 4ºF to 120.2ºF).
•
Storage Temperature:
– 30ºC to 70ºC (– 22ºF to 158ºF).
• Humidity: 20 to 85%, non-condensing.
Functions:
• Auto detection and protection of legacy
non-PoE cameras/devices.
Applications:
• Extend Network link distance in an
industrial environment (see note, pg. 2).
• Works with Megapixel, HD720, HD1080
and VGA (SD) cameras (see note, pg. 2).
Mechanical:
• Dimensions (W x L x H approx.):
3.5” x 3.5” x 1”
(88.9mm x 88.9mm x 25.4mm).
I.T.E. 43KC
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and
with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or
Recognized wire suitable for the application. Pace1PRD is intended for indoor use only.
1.
Pace1PRD installation:
a. Secure unit to desired mounting surface with a proper fastening device utilizing the unit’s
mounting
hole
(Fig. 2a, pg. 3). Unit should be mounted in proximity to ethernet
switch/network, NVR or video server.
b.
Connect structured cable from NetWay1D to RJ45 jack marked [PoE Input] (Fig. 2, pg. 3).
c.
CAT5e or higher: Connect CAT5e or higher cable to connector marked [RJ45 Link]
(Fig. 2, pg. 3).
2.
eBridge200WPM connections:
a. Connect CAT5e from Pace1PRD (60W) to connector marked [CAT INPUT] (Fig. 2, pg. 3)
b. Select input power SW3 on switch marked [60W CAT, 30W CAT or 60W COAX] (Fig. 2, pg. 3).
c.
Connect structured cable from one (1) 60W camera/device to RJ45 jack marked [Port 1] or
connect two (2) individual structured cables from two (2) 30W cameras/devices to RJ45
jacks marked [Port 1] & [Port 2] (Fig. 2, pg. 3).