- 4 -
HubWaAV/DV/Dvi
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | 718-567-8181 | fax: 718-567-9056
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty | Made in U.S.A.
II HubWay Video Balun/Combiners Rev. 123008
B19R
MEMBER
AC Power
to Camera
Data to
Camera
--
+
Data to
Camera
Green Power LED
12VDC Power
to Camera
+
--
Red Power LED
Wire
Connectors
RJ45 Jack
RJ45 Jack
To BNC
Connector
of Camera
To BNC
Connector
of Camera
Structured
Cable from
HubWay,
HubWayLD or
HubSat
Structured
Cable from
HubWay8D
or
HubWay16D
--
+
Wire
Connectors
* Also Available as:
HubWayDvi
Video Balun/
Combiner
for non-isolated
12VDC cameras
Refer to the HubWay Video Balun/Combiner
Installation Guide Rev. 123008
AC
POWER
RJ45
DATA
+ --
VIDEO
Commercial
CCTV Accessory
3C03
HubWayAv
VIDEO BALUN/COMBINER
Refer to the HubWay Video Balun/Combiner
Installation Guide Rev. 123008
12VDC
-- +
RJ45
DATA
+ --
VIDEO
Commercial
CCTV Accessory
3C03
HubWayDv
VIDEO BALUN/COMBINER
Video Balun/Combiner Reference Chart:
Altronix
Model Number
Input Voltage from
HubWay unit
Output Voltage
to camera
Output
Ratings
(max.)
Camera Type
Power
LED
HubWayAv
*24VAC/28VAC
*24VAC/28VAC
1A
24VAC cameras
Green
HubWayDv
*24VAC/28VAC
12VDC
1A
12VDC cameras
Red
HubWayDvi
*24VAC/28VAC
12VDC electronically
isolated
0.5A
12VDC cameras
without isolation
Red
*Based on camera load and structured cable length.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or
moisture. This installation should be made by qualified service personnel and should conform
to all local codes.
Fig. 1
Fig. 1a
Fig. 1b
Overview:
HubWayAv, HubWayDv and HubWayDvi Video Balun/Combiners are UL/cUL Listed accessories that interface
with HubWay and HubSat UTP Transceiver Hubs to transmit video, data, and power to fixed or PTZ indoor or
outdoor cameras.
Note: Refer to HubWay series Rev. 032108, HubWayLD series Rev. 030408 or
HubSat series Rev. 112408 Installation Guides .
HubWayAv passes AC voltage from pins 4, 5, 7, 8 to
terminals marked [AC Power] (Fig. 1, pg. 1).
HubWayDv/Dvi converts AC voltage to DC voltage
from pins 4, 5, 7, 8 to terminals marked
[– 12VDC +] (Fig. 1, pg. 1).
Fig. 1c
Fig. 1d
Agency Listings:
• UL Listed for Commercial CCTV Equipment
(UL 2044).
cUL Listed - CSA Standard C22.2 No.1-04,
Audio, Video and Similar Equipment.
Data:
• Data/PTZ RS422/RS485 output.
Video:
• 75 Ohm video input.
Visual Indicators:
• Power LED indicator.
Specifica tions:
Installation Instructions:
1. Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked [Channel 1] of
the HubWay, HubWayLD, or HubSat Series (Please refer to respective Installation Guides).
Plug the RJ45 connector at the opposite end of the structured cable into the RJ45 jack of the
Video Balun/Combiner installed at camera 1.
• For 24VAC Cameras use Altronix model HubWayAv (Figs. 1a, 1b, pg. 1).
• For 12VDC Cameras use Altronix model HubWayDv/Dvi (Figs. 1c, 1d, pg. 1).
Repeat this step for cameras 2-8.
Note: When an installation exceeds the maximum distance for power transmi ssion, a local external power
source is required. Optionally, an Altronix HubSat4D Passive UTP Transceiver Hub with Integral Power
may be utilized (Fig. 2, pgs. 2-3). The combined total cable distance between the HubWay or HubWayLD
Series and each camera routed through the HubSat4D must not exceed 3000 ft.
2. Measure the output voltage at each Video Balun/Combiner before connecting camera power
(Figs. 1a-1d, pg. 1). This helps avoiding potential damage.
• HubWayAv - Terminals marked [AC POWER] (Figs. 1a, 1b, pg. 1).
• HubWayDv/Dvi - Terminals marked [– 12VDC +] (Figs. 1c, 1d, pg. 1).
3. Connect the power outputs of the HubWayAv or HubWayDv Video Balun/Combiners to the power
input terminals of the cameras (Figs. 1a-1d, pg. 1).
4. Connect the terminals marked [+ DATA –] of the HubWayAv or HubWayDv Video Balun/Combiners
to the data terminals of the cameras for PTZ control (Figs. 1a-1d, pg. 1). Polarity must be observed.
When using fixed cameras disregard this step (Figs. 2, pgs. 2-3).
5. Connect the BNC connector of the HubWayAv. HubWayDv or HubWayDvi Video Balun/Combiners
to the BNC video outputs of the cameras (Figs. 1a-1d, pg. 1).
1
1 - White/Orange [VIDEO +]
2 - Orange [VIDEO -]
3 - White/Green [DATA +]
4 - Blue [AC 1]
5 - White/Blue [AC 2]
6 - Green [DATA -]
7 - White/Brown [AC 2]
8 - Brown [AC 1]
2 3 4 5 6 7 8
Fig. 3 - CAT-5 Structured Cable Wiring Color Codes
Rev. 123008
Installation Guide
HubWayAv, HubWayDv, HubWayDvi
Video Balun/Combiners
