--- DC
+
--- BAT
+
DC
AC
24V - OPEN
12V - CLOSED
L G
N
OFF ON
Door
CAUTION: De-energize unit prior to servicing. For continued protection against
fire hazard replace fuse with the same type and rating 3.5A, 250V.
Replace fuse cover before energizing. Do not expose unit to rain or moisture.
N
COMM
ON POWER
OUTPU
TS
P
FUSED POWER
OUTPUTS
1 2
3 4
5 6
7 8
D1
INPUT
R1
LED
Switch Position:
24VDC = SW1 OPEN
12VDC = SW1 CLOSED
Fuse
Cover
SW1:
24V - OPEN
12V - CLOSED
Switch Position:
24VDC = SW1 OPEN
12VDC = SW1 CLOSED
OFF ON
Power ON/OFF
Switch
Trimpot
Wire Strap
(from
Enclosure
to Door)
Overview:
ALTV1224DC DC CCTV power supply is designed to power CCTV Cameras and accessories. It will provide 12VDC or
24VDC distributed via eight (8) fused outputs with a total of 4 amp total continuous supply current.
Specifications:
Input:
• Input 115VAC 50/60Hz, 1.45 amp.
Output:
• Eight (8) individual fused outputs.
• 4 amp total continuous supply current.
• 12VDC or 24VDC selectable output.
Fuse Ratings:
• Input fuse rated at 3.5 amp / 250V.
• Output fuses are
rated at 1 amp / 250V
(Fig. 1).
Visual Indicators:
• AC input and DC output LED indicator.
Additional Features:
• Filtered and electronically regulated outputs.
• Power ON/OFF switch.
• Spare fuses included.
• Unit maintains camera synchronization.
• Ease of installation saves time and
eliminates costly labor.
Enclosure Dimensions:
13.5"H x 13"W x 3.25"D
Optional
220VAC input available order
model # ALTV1224DC/220.
Power Supply Output Specifications:
Output
Switch
Maximum
VDC
Position
Load DC
12VDC
SW1 Closed
4 amp
24VDC
SW1 Open
4 amp
Installation Instructions:
1. Mount ALTV1224DC enclosure in desired locations.
2. Slide switch to OFF position
(Fig. 1A)
.
3. Set the ALTV1224DC to desired DC output voltage range by setting switch (SW1) on the power supply
board to the appropriate position
(Power Supply Output Specification Table) (Fig. 1C).
Use trimpot to adjust voltage if necessary
(Fig. 1B)
.
4. Connect the AC (115VAC 50/60 Hz) to the terminals marked L and N. Connect earth ground to G terminal
(Fig. 1)
.
5.
Measure output voltage before connecting devices.
This helps avoid potential damage.
6. Connect each DC device to output terminals 1 through 8.
(Fig. 1)
.
Note:
Be careful to observe camera polarity.
7. When batteries are being used the DC output voltage must be adjusted by turning the trim pot VR1
(Fig. 1B)
clockwise to increase the output voltage to 13.7VDC for 12VDC operation and 27.1VDC for 24VDC operation.
Connect battery to terminals marked [-- BAT + ] (battery leads included)
(Fig. 1)
.
Use two (2) 12VDC batteries connected in series for 24VDC operation.
8. Slide switch to ON position
(Fig. 1A)
.
9. Green LED on the PD8 board will illuminate when power is present.
10. Upon completion of wiring, secure enclosure door with screws (supplied).
ALTV1224DC
CCTV Camera & Accessory Power Supply
Fig. 1A
Fig. 1B
Fig. 1
Fig. 1C
