background image

Page 8

Work Light II

Installation & Users Manual

C-Clamp Installation

The provided c-clamp should be installed as shown in 

Figure 2

. Only use the hardware supplied with the

c-clamp.

To Install the C-clamp:

1.  With luminaire on a flat, sturdy surface, position yoke assembly for easy access as illustrated in 

Figure 2

.

2.  Place on 1/2-13 hex bolt, in this order, the 1/2-inch lock washer and then the 1/2-inch flat washer.
3.  Insert bolt into hole on yoke assembly.
4.  Position c-clamp over bolt and thread bolt into c-clamp.
5.  Tighten bolt.

Safety Cable Installation

The provided safety cable should be installed in accordance to local and national codes.

NOTE

: The safety cable (supplied with unit) 

should be used and may be required by local 

and/or national codes when hanging this    

luminaire. The mounting structure must be 

capable of supporting the weight of the fixture, 

lens, cabling, any accessories, etc.

C-Clamp
Worklight II Yoke 

1/2-inch (13mm) Mounting Hole

1/2-inch Flat Washer

1/2-inch Lock Washer

1/2-13 Hex Bolt

C-Clamp

Safety Cable Anchor Point

Figure 2: C-Clamp Installation

Содержание WORK LIGHT II












Отзывы: