Maintenance
It is important to stablish a routin for th
storag of fu l, starting th fier , and caring for th
unit so as not to ov rlook important asp cts of
saf ty, and to maintain th unit in optimum
condition. Maintaining th load door s al and air
valv gask t s al ar v ry important for fficci ncy,
and for saf ty.
WEEKLY CLEANING PROCEDURE
Following is th r comm nd d proc dur for
w kly cl aning:
1. Allow th Boil r to cool and us glov s.
2. Op n front insp ction door.
3. Plac an ash r c iv r und r th r fractory at th
front insp ction door op ning.
4. R mov th upp r plug. Us th ash rak to pull
th ash from th upp r chamb r.
5. R mov th r strictor plug from th low r
chamb r and us th ash rak to pull th ash from
th low r chamb r.
6. R -ins rt th upp r plug in th upp r chamb r
and v rify that it prop rly s als th front acc ss
op ning.
7. R -ins rt th r strictor plug in th low r
chamb r.
8. Us a puttay knif or scrap r to cl an ash from
th bottaom of th door op ning.
9. Op n th air-valv cov r and insp ct th valv
gask t disks for vid nc of air l akag . The disk
should hav som wobbl , so it can mov and fiend its
own s al. S “
Air Valve Cleaning and
Maintenance”
b low.
10. Scrap cond nsation and cr osot build-up
from insid th air intak manifold using ash rak .
11. Cl an xc ssiv ash out of fier box.
Air Valve Cleaning and Maintenance
To Op rat th Air Valv Manually for Cl aning
and S rvic :
1. Mak sur th SE210 is not in Wood or Oil
mod , that th wat r t mp is b low 130F and that th
xhaust t mp is b low 95F.
2. Go to th “Maint nanc ” scr n and pr ss
“Cl aning Mod ”
3. Onc in th “Cl aning Mod ” you will s
buttaons for th 1
st
Air-Valv , 2
nd
Air-Valv , and th
Drafte fan. Wh n you turn on th Air-Valv s, th y
will op n so you can cl an or r plac th ir discs.
The air valv should b insp ct d and cl an d
w kly to nsur that it is s aling prop rly. A l aking
air valv or load door can produc a numb r of
und sirabl cons qu nc s, including a low
smold ring fier . Wh n th air valv is op n and th
unit is op rating, moistur r l as d from th fu l will
cond ns wh n contact is mad with cool r
combustion air. Moistur and cr osot can coll ct on
th gask t disk and on th nd of th air valv tub
- 38 -
The air valve may be inspected
during the “run” cycle of the boiler.
Any cleaning or service to the air
valve should be performed when
there is no fire in the combustion
chamber and is in the “Cleaning
Mode”.
The unit must be out or cycle off for
at least four hours and the power
must be disconnected before
attempting to clean or service.
Note: The front of the top combustion chamber
must be properly sealed to prevent gas from
being drawn directly into the heat exchanger
thereby bypassing the refractory.
Содержание WOOD GUN Super E210
