manualshive.com logo in svg

Altera Cyclone V, Руководство по эксплуатации устройства, Страница: 347 / 1077

Поделиться
Скачать
Altera Cyclone V Скачать руководство пользователя страница 347

The contiguous channels may span across many banks for bonded mode. For example, in x8 bonding,
the bonded channels may span across 3 to 4 banks with the condition that there must be no gap
between the channels except when the gap is due to the channel used for CMU PLL.

Transmitter Clocking

Transmitter (TX) clocking refers to the clocking architecture that is internal to the TX channel of a transceiver.

As shown in the following figure, the clock divider provides the serial clock to the serializer, and the parallel
clock to the serializer and TX PCS. When the byte serializer is not used, the parallel clock clocks all the blocks
up to the read side of the TX phase compensation FIFO. For configurations with the byte serializer, the
parallel clock is divided by a factor of two for the byte serializer and the read side of the TX phase
compensation FIFO. The read side clock of the TX phase compensation FIFO is also forwarded to the FPGA
fabric to interface the FPGA fabric with the transceiver.

Figure 2-8: Clocking Architecture for Transmitter PCS and PMA Configuration

Transmitter PCS

Transmitter PMA

FPGA Fabric

TX

Phase

Compensation

FIFO

Byte

Serializer

8B/10B

Encoder

TX

Bit

Slip

Serializer

tx_serial_data

tx_parallel_data

/2

tx_coreclkin /
tx_std_coreclkin

tx_clkout /
tx_std_clkout

Both Parallel and Serial Clocks

Local/Central
clock divider

Serial Clock

Parallel Clock

Data Path

Transmitter

Table 2-5: Clock Sources for All TX PCS Blocks

Clock Source

Side

PCS Block

FPGA fabric write clock, driven either by tx_clkout or tx_
coreclkin

Write

TX Phase Compensation
FIFO

Parallel clock (divided). Clock forwarded to FPGA fabric as tx_
clkout

Read

Parallel clock (divided) either by factor of 1 (not enabled), or
factor of 2 (enabled)

Write

Byte Serializer

Parallel clock

Read

Parallel clock

—

8B/10B Encoder

Parallel clock

—

TX Bit Slip

Non-Bonded Channel Configurations

This section describes the clock path for non-bonded configurations.

The following table describes the clock path for non-bonded configuration with the CMU PLL and fPLL as
TX PLL using various clock lines.

Altera Corporation

Transceiver Clocking in Cyclone V Devices

Send Feedback

2-9

Transmitter Clocking

CV-53002
2013.05.06

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов