manualshive.com logo in svg

Altera Cyclone V, Руководство по эксплуатации устройства, Страница: 26 / 1077

Поделиться
Скачать
Altera Cyclone V Скачать руководство пользователя страница 26

Figure 2-5: Mixed-Port Read-During-Write: Don’t Care or Constrained Don’t Care Mode

This figure shows a sample functional waveform of mixed-port read-during-write behavior for the “don’t
care” or “constrained don’t care” mode.

clk_a&b

wren_a

address_a

A0

A1

data_a

byteena_a

rden_b

address_b

q_b (asynch)

XXXX (unknown data)

A0

A1

11

11

01

10

AAAA

BBBB

CCCC

DDDD

EEEE

FFFF

In the dual-port RAM mode, the mixed-port read-during-write operation is supported if the input registers
have the same clock. The output value during the operation is “unknown.”

Related Information

Internal Memory (RAM and ROM) User Guide

Provides more information about the RAM megafunction that controls the read-during-write behavior.

Guideline: Consider Power-Up State and Memory Initialization

Consider the power up state of the different types of memory blocks if you are designing logic that evaluates
the initial power-up values, as listed in the following table.

Table 2-4: Initial Power-Up Values of Embedded Memory Blocks

Power Up Value

Output Registers

Memory Type

Zero (cleared)

Used

MLAB

Read memory contents

Bypassed

Zero (cleared)

Used

M10K

Zero (cleared)

Bypassed

By default, the Quartus II software initializes the RAM cells in Cyclone V devices to zero unless you specify
a .mif.

All memory blocks support initialization with a .mif. You can create .mif files in the Quartus II software
and specify their use with the RAM megafunction when you instantiate a memory in your design. Even if a
memory is pre-initialized (for example, using a .mif), it still powers up with its output cleared.

Embedded Memory Blocks in Cyclone V Devices

Altera Corporation

Send Feedback

CV-52002

Guideline: Consider Power-Up State and Memory Initialization

2-6

2013.05.06

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов