manualshive.com logo in svg

Altera Cyclone V, Руководство по эксплуатации устройства, Страница: 166 / 1077

Поделиться
Скачать
Altera Cyclone V Скачать руководство пользователя страница 166

Figure 5-43: On-Chip Differential I/O Termination

Differential Receiver

with On-Chip 100 Ω

Termination

LVDS

Transmitter

Z

0

= 50 Ω

Z

0

= 50 Ω

R

D

Table 5-41: Quartus II Software Assignment Editor—On-Chip Differential Termination

This table lists the assignment name for on-chip differential termination in the Quartus II software Assignment
Editor.

Assignment

Field

rx_in

To

Input Termination

Assignment name

Differential

Value

Source-Synchronous Timing Budget

The topics in this section describe the timing budget, waveforms, and specifications for source-synchronous
signaling in the Cyclone V device family.

The LVDS I/O standard enables high-speed transmission of data, resulting in better overall system
performance. To take advantage of fast system performance, you must analyze the timing for these high-
speed signals. Timing analysis for the differential block is different from traditional synchronous timing
analysis techniques.

The basis of the source synchronous timing analysis is the skew between the data and the clock signals instead
of the clock-to-output setup times. High-speed differential data transmission requires the use of timing
parameters provided by IC vendors and is strongly influenced by board skew, cable skew, and clock jitter.

This section defines the source-synchronous differential data orientation timing parameters, the timing
budget definitions for the Cyclone V device family, and how to use these timing parameters to determine
the maximum performance of a design.

Differential Data Orientation

There is a set relationship between an external clock and the incoming data. For operations at 840 Mbps
and a serialization factor of 10, the external clock is multiplied by 10. You can set phase-alignment in the
PLL to coincide with the sampling window of each data bit. The data is sampled on the falling edge of the
multiplied clock.

Altera Corporation

I/O Features in Cyclone V Devices

Send Feedback

5-69

Source-Synchronous Timing Budget

CV-52005
2014.01.10

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов