Altera Arria V GZ Скачать руководство пользователя страница 233

Страница: 233 / 300

Chapter 15: Hard IP Reconfiguration and Transceiver Reconfiguration

15–9

Transceiver PHY IP Reconfiguration

November 2012

Altera Corporation

Arria V GZ Hard IP for PCI Express

User Guide

Transceiver PHY IP Reconfiguration

As silicon progresses towards smaller process nodes, circuit performance is affected
by variations due to process, voltage, and temperature (PVT).

Figure 15–1

shows the

reconfiguration functions required for Gen1, Gen2, and Gen3 variants.

You must disable offset cancellation if your design includes CvP.

Connecting the Transceiver Reconfiguration Controller IP Core

You can instantiate this component using the MegaWizard Plug-In Manager or Qsys.
It is available for Arria V GZ devices and can be found in the

Interfaces/Transceiver

PHY

category for the MegaWizard design flow. In Qsys, you can find the Transceiver

Reconfiguration Controller in the

Interface Protocols/Transceiver PHY

category.

When you instantiate your Transceiver Reconfiguration Controller IP core the

Enable

offset cancellation block

option is

by default. For Gen3 variants, you should also

turn on adaptive equalization.

Figure 15–1

shows the connections between the Transceiver Reconfiguration

Controller instance and the PHY IP Core for PCI Express instance for a ×4 variant.

Table 15–1. Re

Data Rate

Required Reconfiguration Functions

Gen1 and Gen2

Offset cancellation

Gen3

Offset cancellation and adaptive equalization (AEQ)

Figure 15–1. Altera Transceiver Reconfiguration Controller Connectivity

Avalon-MM

Slave Interface

PHY IP Co

e fo

PCI Exp

ess

Lane 2

Lane 3

Lane 1

Lane 0

TX PLL

ansceive

Bank

100-125 MHz

ansceive

Reconfigu

ion Con

olle

(Unused)

mgmt_clk_clk
mgmt_rst_reset
reconfig_mgmt_address[6:0]
reconfig_mgmt_writedata[31:0]
reconfig_mgmt_readdata[31:0]
reconfig_mgmt_write
reconfig_mgmt_read
reconfig_mgmt_waitrequest

reconfig_to_xcvr

reconfig_from_xcvr

d IP fo

PCI Exp

ess Va

ian

d IP fo

PCI Exp

ess

ans-

ion

Link

PHY

Содержание Arria V GZ













































































































































































































































































































Результаты поиска

Содержание Arria V GZ

Отзывы:

Похожие инструкции для Arria V GZ

Бренды по названию

Популярные бренды

Altera Arria V GZ, Руководство пользователя

Результаты поиска

Содержание Arria V GZ

Отзывы:

Похожие инструкции для Arria V GZ

Бренды по названию

Популярные бренды