manualshive.com logo in svg

Altec ATP-4310, Руководство пользователя

Поделиться
Скачать
Altec ATP-4310 Скачать руководство пользователя страница 52

- 45 -

5.5

 

 Sensor 

This option is used to calibrate the selected sensor. We recommend calibrate the sensor 

before printing when changing the media. 

Item 

Description 

Default 

Auto 
Calibration 

This option is used to set the media sensor type and calibrate 
the selected sensor automatically. Printer will feed 2 to 3 gap 
labels to calibrate the sensor sensitivity automatically. 

N/A 

Manual setup 

In case “Automatic” cannot apply to the media, please use 
“Manual” function to set the paper length and gap/bline size 
then scan the backing/mark to calibrate the sensor sensitivity. 

N/A 

Threshold 
Detect 

This option is used to set sensor sensitivity in fixed or auto. 

Auto 

Maximum 
Length 

This option is used to set the maximum length for label 
calibration. 

254 

mm 

Advanced 

This function can set the minimum paper length and maximum 
gap/bline length for auto-calibrate the sensor sensitivity.

 

N/A 

Menu 

Sensor 

Auto Calibration 

Gap 

Black Mark 

Continuous 

Manual Setup 

Gap 

Black Mark 

Continuous 

Threshold Detect 

Auto 

Fixed 

Maximum Length 

Advanced 

Содержание ATP-4310


























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды