ALPINE VPA-B222R 68-06194Z40-A (EN)
English
L
Add to “In Case of Difficulty” in the Owner’s Manual (page 46) the following settings and operations for FACTORY
SYSTEM (Speaker Input).
Speaker input sound is distorted.
• The Factory system has already been adjusted.
- If the following settings of the car's Factory System: BASS, TREBLE, LOUDNESS, etc., are performed while in speaker input
mode, the Factory System sound is easily distorted. Therefore reset the above settings.
• The volume is not appropriately adjusted.
- Set the speaker input volume level (FACT SYS LV) to less than 15. Then, lower the car's Factory System volume, so that sound is
not distorted. Refer to “Displaying the Speaker Input Volume Level” (page 16).
Malfunction.
• A malfunction occurs caused by speaker input cable noise.
- Bundle and route the
e
and
d
speaker input cables. Routing the speaker input cables separately may cause noise.
The volume of the car audio system is too high/low.
• The volume is not appropriately adjusted.
- Select FACTORY SYS on the source selection screen, and adjust the volume using the commander.
Interruption does not function correctly.
• The speaker input is not correctly set to detect the Factory System.
- Make sure that the speaker cable of the car's Factory System properly connected. Confirm that the input is correctly selected
according to the detection channel setting (F.SYS INT CH.). Refer to “Setting the Channel of the Speaker Interruption Detection”
(page 17).
• Interruption volume of the car's Factory System is too low.
- 1) When an external audio processor is connected, set the GUIDE voice to 15. Refer to “Adjusting Volume of GUIDE Voice”
(page 12).
- 2) While the navigation voice guidance or the telephone audio of the car's Factory System is ON, set the speaker input volume level
(FACT SYS LV). The sound should be clearly audible, but the level should not exceed 15. Adjust the volume of the car's Factory
System if necessary. Refer to “Displaying the Speaker Input Volume Level” (page 16).
If the speaker input volume level is lower than the detection level (FACT SYS DET), interruption will not occur. Refer to
“Adjusting the Speaker Input’s Interruption Detection Level” (page 17).
• Interruption occurs too frequently because the detection level is set too low.
- Raise the interruption detection level (FACT SYS DET). Refer to “Adjusting the Speaker Input’s Interruption Detection Level”
(page 17).
• Interruption does not occur frequently enough if the detection level is set too high.
- Lower the interruption detection level (FACT SYS DET). Refer to “Adjusting the Speaker Input’s Interruption Detection Level”
(page 17).
• The source is set to FACTORY SYS.
- Change to another source. If the source is set to FACTORY SYS while listening to the Factory audio system, sound is output to all
speakers without interrupting the front speaker for the navigation voice guidance or telephone voice.
• Depending on the type of telephone ring tone, interruption may not be recognized.
- Lower the interruption detection level (FACT SYS DET), or change the telephone ring tone. Refer to “Adjusting the Speaker Input’s
Interruption Detection Level” (page 17).
• Depending on the car, the telephone volume is automatically lowered. Therefore, interruption is not recognized.
- Lower the interruption detection level (FACT SYS DET) based on the car's Factory System level. Refer to “Adjusting the Speaker
Input’s Interruption Detection Level” (page 17).
Interruption volume of the car navigation system is too high/low.
• The volume is not appropriately adjusted.
- Set the interruption volume (FACT SYS MIX) appropriately. Refer to “Adjusting the Speaker Input Voice Interruption Level”
(page 17).
To customers/Hinweis an Kunden/
A l’attention de l’utilisateur/Información para
los clientes/Informazioni per i clienti/Till kunder
R
EN
