32
-EN
No picture is produced.
•
Monitor's mode is not switched to the mode you want to see.
- Switch to the mode you want to see.
•
Monitor's parking brake cord is not connected.
- Connect the monitor's parking brake cord and set the parking
brake. (For details, refer to the monitor's instructions.)
•
Monitor's parking brake is not set.
- Connect the monitor's parking brake cord and set the parking
brake. (For details, refer to the monitor's instructions.)
Playback does not start.
•
Disc is loaded upside-down.
- Check the disc and load it with the labeled side facing
upward.
•
The disc is dirty.
- Clean the disc.
•
A disc not able to playback with this unit is loaded.
- Check if the disc is able to be played back.
•
Parental lock is set.
- Cancel the parental lock or change the rating level.
•
Setup menu is displayed.
-
Press
SETUP
to turn the menu off.
Picture is unclear or noisy.
•
Disc is being fast-forwarded or fast-reversed.
- The picture may be unclear, but this is normal.
•
Vehicle's battery power is weak.
- Check the battery power and wiring.
(The unit may malfunction if the battery power is under 11
volts with a load applied.)
•
Monitor's
fl uorescent tube is worn out.
- Replace the monitor's fl uorescent tube.
Image stops sometimes.
•
Disc is scratched.
- Replace with a non-scratched disc.
No picture display.
•
Brightness control is set for minimum brightness control.
- Adjust the brightness.
•
Incorrect setting of the mode.
- Switch to the correct mode.
- Check the connection to the source unit.
- Check the power of the source unit.
•
Incorrect or open connection with the Monitor, AV interface
unit.
- Check the connection and remedy.
Picture color is poor.
•
Brightness/Color/Tint/Contrast/Sharpness control are not set to
the proper positions.
- Check each control.
Spots or dotted lines/stripes appear.
•
Caused by neon signs, high-voltage power lines, CB
transmitter, other vehicle’s ignition plugs, etc.
- Change the location of your vehicle.
Unit does not operate.
•
Monitor’s power is not turned on.
- Turn on the monitor’s power.
Due to continuous product improvement, specifi cations and
design are subject to change without notice.
In Case of Diffi culty
If you encounter a problem, please turn the power off, then on
again. If the unit is still not functioning normally, please review the
items in the following checklist. This guide will help you isolate the
problem if the unit is at fault. Otherwise, make sure the rest of your
system is properly connected or consult your authorized Alpine
dealer.
No function or display.
•
Vehicle's ignition is off.
- If connected following the instructions, the unit will not
operate with the vehicles ignition off.
•
Improper power lead connections.
- Check power lead connections.
•
No fuse or blown fuse.
- Replace the fuse on the battery lead of the unit with the
proper value.
•
Vehicle’s battery is weak.
- Check the voltage of vehicle’s battery.
Disc playback sound is wavering.
•
Moisture condensation in the disc unit.
- Allow enough time for the condensation to evaporate (about
1 hour).
Disc insertion not possible.
•
A disc is already in the DVD player.
- Eject the disc and remove it.
•
The disc is being improperly inserted.
- Re-insert the disc following the instructions in the "Loading
and Unloading Discs" section.
Unable to fast forward or reverse the disc.
•
The disc has been damaged.
- Eject the disc and discard it; using a damaged disc in your
unit can cause damage to the mechanism.
Disc playback sound skips due to vibration.
•
Improper mounting of the unit.
- Securely re-mount the unit.
•
The disc is very dirty.
- Clean the disc.
•
The disc has scratches.
- Change the disc.
•
The pick-up lens is dirty.
- Do not use a commercial available lens cleaner disc.
Consult your nearest ALPINE dealer.
Disc playback sound skips without vibration.
•
Dirty or scratched disc.
- Clean the disc; damaged disc should be replaced.
CD-R/CD-RW playback not possible.
•
Close session (fi nalization) has not been performed.
-
Perform
fi nalization and attempt playback again.
Error displays
•
Mechanical
error
-
Press . After the error indication disappears, insert the disc
again. If the above-mentioned solution does not solve the
problem, consult your nearest ALPINE dealer.
Unit does not operate.
•
Monitor's power is not turned on.
- Turn on the monitor's power.
•
Condensation
- Wait a while (about 1 hour) for the condensation to dry.
Содержание PKG-2100P
Страница 2: ......
