Alpine IVE-W560BT, Руководство пользователя

Страница: 28 / 96

28
-EN
Before installing or connecting the unit, please read the
following and pages 4 to 9 of this manual thoroughly for
proper use.
Warning
MAKE THE CORRECT CONNECTIONS
Failure to make the proper connections may result in fi re or product
damage.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may
result in
fi re, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE
NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to
electrical shorts.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN
SURROUNDING OBJECTS.
Arrange wiring and cables in compliance with the manual to
prevent obstructions when driving. Cables or wiring that obstruct
or catch on locations such as the steering wheel, gear lever, brake
pedals, etc. can be extremely hazardous.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity of
the wire and result in
fi re or electric shock.
DO NOT DAMAGE PIPES OR WIRING WHEN DRILLING HOLES.
When drilling holes in the chassis for installation, take precautions
so as not to contact, damage or obstruct pipes, fuel lines, tanks or
electrical wiring. Failure to take such precautions may result in
fi re.
DO NOT USE NUTS OR BOLTS IN THE BRAKE OR STEERING
SYSTEMS TO MAKE GROUND CONNECTIONS.
Nuts and bolts used for the brake or steering systems (or any
other safety-related system), or tanks should NEVER be used for
installations or ground connections. Using such parts could disable
control of the vehicle and cause
fi re etc.
KEEP SMALL OBJECTS SUCH AS BOLTS OR SCREWS OUT OF
THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed, consult
a doctor immediately.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER
VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR
GEAR LEVER.
Doing so may obstruct forward vision or hamper movement etc.
and results in serious accident.
Caution
ONLY TO BE INSTALLED BY A QUALIFIED ELECTRICIAN OR
VEHICLE TECHNICIAN.
The wiring and installation of this unit requires special technical
skill and experience. To ensure safety, always contact the dealer
where you purchased this product to have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM
SECURELY.
Be sure to use only the speci fi ed accessory parts. Use of other
than designated parts may damage this unit internally or may not
securely install the unit in place. This may cause parts to become
loose resulting in hazards or product failure.
ROUTE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A
SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the seat
rails) or sharp or pointed edges. This will prevent crimping and
damage to the wiring. If wiring passes through a hole in a metal
component, use a rubber grommet to prevent the wire’s insulation
from being cut by the metal edge of the hole.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR
DUST.
Avoid installing the unit in locations with a high level of moisture
or dust. Moisture or dust that penetrates into this unit may result in
product failure.
Precautions
• Disconnect the cable from the (–) battery terminal before
installing your IVE-W560BT/IVE-W560BT-R. This will reduce
any chance of damage to the unit in the event of a shortcircuit.
• Be sure to connect the colour coded leads according to
the diagram. Incorrect connections may cause the unit to
malfunction or damage the vehicle’s electrical system.
• When making connections to the vehicle’s electrical system,
be aware of the factory installed components (e.g. on-board
computer). Do not tap into these leads to provide power for this
unit. When connecting the IVE-W560BT/IVE-W560BT-R to
the fuse box, make sure the fuse for the intended circuit of the
IVE-W560BT/IVE-W560BT-R has the appropriate amperage.
Failure to do so may result in damage to the unit and/or the
vehicle. If in doubt, consult your ALPINE dealer.
• The IVE-W560BT/IVE-W560BT-R uses female RCA-type
jacks for connection to other units (e.g. ampli fi er) having RCA
connectors. You may need an adapter to connect other units. If
so, please contact your authorized ALPINE dealer for assistance.
• Be sure to connect the speaker (–) leads to the speaker (–)
terminal. Never connect left and right channel speaker cables to
each other or to the vehicle body.
• The Display must be completely retracted in the casing when
installing. If not, problems may occur.
• When installing in vehicles, make sure the display can open/
close without coming in contact with the gear lever.
IMPORTANT
Please record the serial number of your unit in the space provided
below and keep it as a permanent record. The serial number plate
is located on the bottom of the unit.
SERIAL NUMBER:
INSTALLATION DATE:
INSTALLATION TECHNICIAN:
PLACE OF PURCHASE:
Installation and Connections