ALPINE HCE-C300R_EN 68-18693Z26-B (A5)
3
-EN
or
ersa
to
d as
to
r
TING
RE
OR
N A
D
OR,
g
.
OUT
ed,
NG
MAKE THE CORRECT CONNECTIONS.
When making connections to the vehicle’s electrical system,
be aware of the factory installed components (e.g. on-board
computer). Do not tap into these leads to provide power
for this unit. When connecting the device to the fuse box,
make sure the fuse for the intended circuit of the device has
the appropriate amperage. Failure to do so may result in fire
or damage to the unit and/or the vehicle. When in doubt,
consult your Alpine dealer.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE
NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to
electrical shorts.
DO NOT ROUTE ELECTRICAL CABLES NEAR HOT OR
MOVING PARTS.
Route the cables and wiring away from hot or moving parts,
and fix them securely to avoid heat/mechanical damage to
the cable insulation, which may result in a short circuit, fire
or electric shock.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying
capacity of the wire and result in fire or electric shock.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER
VEHICLE OPERATION, SUCH AS THE STEERING WHEEL
OR SHIFT LEVER.
Doing so may obstruct forward vision or hamper movement
etc. and results in serious accident.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING
HOLES.
When drilling holes in the chassis for installation, take
precautions so as not to contact, damage or obstruct pipes,
fuel lines, tanks or electrical wiring. Failure to take such
precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR
STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any
other safety-related system), or tanks should NEVER be used
for installations or ground connections. Using such parts
could disable control of the vehicle and cause fire etc.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN
SURROUNDING OBJECTS.
Arrange wiring and cables in compliance with the manual
to prevent obstructions when driving. Cables or wiring that
obstruct or hang up on places such as the steering wheel, shift
lever, brake pedals, etc. can be extremely hazardous.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire,
electric shock or other injury.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so
may result in fire, etc.
WHEN USING A DRILL TO MAKE A HOLE, TAKE
PRECAUTIONS SUCH AS WEARING GOGGLES SO
FRAGMENTS DO NOT GET INTO THE EYES.
Failure to do so may result in injury.
CALIBRATION REQUIRED.
If this camera system is not calibrated, its detection function
will not work properly. It must be calibrated before use.
Calibration is also necessary after remounting.
BE CAREFUL WHEN SETTING THE ALARM VOLUME.
Set the alarm volume to an audible level. If the alarm cannot
be heard due to the volume of the car radio, etc., it might
result in an accident.
BE AWARE OF DIFFERENCES IN DETECTION SENSITIVITY
LEVELS.
If the sensitivity level of the object detector is changed
from a high setting to a low setting, be aware of differences
in detection levels. Objects that were detected under the
previous level will not be detected anymore, and this might
result in an accident.
BE AWARE OF THE OPERATING CONDITIONS OF THE
OBJECT DETECTION FUNCTION.
The warning function only works when the gear lever is in
the reverse position (R). Using the detection feature with
reverse OFF may result in an accident.
DO NOT USE WITH A TOW TRUCK.
If reversed while connected to a tow truck, it will falsely
detect the tow truck. Also, it cannot detect objects near the
tow truck, which may result in an accident.
DO NOT JUDGE SITUATIONS BASED ONLY ON THE
WARNING OF THE OBJECT DETECTION FUNCTION.
Warnings may not always be given even when vehicles or
people are in danger of being hit. This is due to many factors
such as vehicle speed or distance from your vehicle.
DO NOT IGNORE OBJECT DETECTION FUNCTION
WARNINGS.
If an object detection warning occurs, check the surrounding
area thoroughly.
CAUTION
This symbol means important instructions.
Failure to heed them can result in injury or
material property damage.
DO NOT ATTACH THE CAMERA AND/OR OBJECT SENSOR
MOUNTING TO FLUOROCARBON RESIN FINISHED CAR
BODIES OR GLASS.
Doing so could cause the strength of the camera mounting to
weaken, which could cause it to fall of and cause accidents,
injury, or damage to the car body.
DO NOT ATTACH THE CAMERA AND/OR OBJECT SENSOR
MOUNTING TO ANY SURFACE WHERE THE ENTIRE
ADHESIVE SURFACE CANNOT BE APPLIED.
Doing so could cause the strength of the camera mounting to
weaken, which could cause it to fall of and cause accidents,
injury, or damage to the car body.
EXCEPT FOR THE CAMERA AND/OR OBJECT SENSOR, DO
NOT ATTACH ANY PARTS TO AREAS WHICH WILL GET
WET, OR WHERE THERE IS A LOT OF HUMIDITY OR DUST.
Failure to do so may result in fire or damage.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM
SECURELY.
Be sure to use only the specified accessory parts. Use of other
than designated parts may damage this unit internally or may
not securely install the unit in place. This may cause parts to
become loose resulting in hazards or product failure.
