background image

ALPINE HCE-C300R_EN 68-18693Z26-B (A5)

11

-EN

Camera Image

With HCE-C300R, you can select and switch 
image configurations.
The guidelines display varies with the image 
configuration.
For details on how to switch image 
configurations, refer to “Camera Operation” (page 
15)

The guidelines shown here are for illustrative 
purposes only. The guidelines in the actual image 
will be different.

Corner View

Rear View

Panorama View 

(180°)

Corner View

Ground View

Panorama View:

Displays a general perspective of what is behind 
the car. Use this when you want to view a wider 
than normal area behind the car.

Rear View:

Displays what is directly behind the car. Use this 
when reversing into a parking space, for example.

Ground View:

Displays an image down to the lower section of 
the car. Use this to determine the car’s position in 
relation to the curb, etc.

Corner View:

Displays a divided image left and right of centre. 
Use this mainly when checking the left and right 
directional view.

No guidelines appear in Corner View.
The rearview camera image is reversed to have the 
same perspective as the rearview mirror. However, 
due to the camera’s fisheye lens, there is a distortion 
of the actual distance as it appears in the display.
Images may not be clearly displayed in the following 
conditions. This is normal.

In the dark (nighttime, etc.)
The temperature near the lens is high or low.
The camera has water droplets on it or the 
humidity is high (rainy day, etc.).
Foreign substances (dirt, etc.) are on or around the 
camera.
Sun light or the light of a headlamp directly enters 
the camera lens.

The guidelines in the display may not always 
correspond to actual distances from objects being 
viewed. Factors such as road surface, number of 
passengers, load weight, suspension adjustments, 
etc. can affect the accuracy of the display. Always use 
visual inspection to verify safe driving conditions of 
your surroundings.




Содержание HCE-C300R








































Отзывы: